User manual HP CONTURA AERO

[. . . ] Notice The information in this guide is subject to change without notice. Compaq Computer Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation. [. . . ] >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>><<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 1. Attach the inverter board LIF connector to the display cable. Attach the backlight cable to the inverter board. Align the inverter board with the three mounting posts. Liquid Crystal Display Panel To remove the backlit liquid crystal display (LCD) panel, follow these steps: 1. Remove the display bezel (Figures 3-5 and 3-6). Remove the remaining two top left screws and the one top right screw that secure the LCD panel to the display enclosure (Figure 3-18). Remove the top clutch screw and ground clip bracket in the bottom right corner of the display enclosure (Figure 3-18). 4. Carefully rotate the LCD panel to the left and out of the display enclosure (Figure 3-19). 5. Remove the display cable from the rear of the LCD panel by gently pulling the cable toward you (Figure 3-20). Carefully lift up on the ZIF connector to release the display cable from the side of the LCD panel (Figure 3-20). To replace the LCD panel, follow these steps: 1. Remove the pressure sensitive adhesive backing from the back of the display cable. Align the holes in the cable with the mounting pins on the display enclosure. Connect the display cable to the LCD panel with the ZIF connector. Lay the LCD panel into the display enclosure with the bottom of the display cable exposed. Secure the LCD panel with three screws to the display enclosure. Secure the support bracket with one screw in the bottom right corner of the display enclosure. Latch, Clutch, Pin, and Display Shield To remove and replace the latch from the middle of the display enclosure, the clutch, pin, and the display shield, follow these steps (Figure 3-21): 1. Using a small flat bladed screwdriver, remove the spring from the latch. Pry the latch away from the display enclosure. Using a Phillips screwdriver, remove the remaining screw from the clutch and then remove the clutch out of the display enclosure. Remove the two screws from the pin and remove the pin from the display enclosure. 5. Remove the display shield by lifting it out of the display enclosure (Figure 3-22). To replace the display shield, lay it inside of the display enclosure. To replace the latch, attach the spring to the latch and snap them into the display enclosure. To replace the clutch and pin, reverse the previous steps. [. . . ] Error =========================================================================== Chapter 6. Specifications Chapter 6. 0 Introduction This chapter provides physical, environmental, and performance specifications for the following Compaq Contura Aero Family of Personal Computer subsystems: o o o o o o o o Computer VGA Display Hard Drives Internal Power Supply NiMH Battery Pack AC Adapter Base Unit External Diskette Drive Chapter 6. 1 System Unit =========================================================================== U. S. Metric =========================================================================== Dimensions: Contura Aero 4/25 Height 1. 53 in 3. 81 cm Width 10. 25 in 26 cm Depth 7. 5 in 19 cm Contura Aero 4/33C Height 1. 7 in 4. 32 cm Width 10. 25 in 26 cm Depth 7. 5 in 19 cm --------------------------------------------------------------------------Weight (approximate): Contura Aero 4/25 Model 84 (standard battery) 3. 5 lbs 1. 59 kg Model 84 (extended life) 3. 9 lbs 1. 77 kg Model 170 (standard battery) 3. 6 lbs 1. 63 kg Model 170 (extended life) 4. 0 lbs 1. 81 kg Contura Aero 4/33C Model 170 4. 3 lbs 1. 95 kg --------------------------------------------------------------------------Power Requirements 10. 8V 10. 8V --------------------------------------------------------------------------Environmental Requirements: Temperature Operating 50oF to 104oF 10oC to 40oC Nonoperating -4oF to 140oF -20oC to 60oC --------------------------------------------------------------------------Relative Humidity (noncondensing): Operating 10% to 90% 10% to 90% Nonoperating 5% to 95% 5% to 95% --------------------------------------------------------------------------Shock and Vibration Shock Operating 10g, 11ms, half sine Nonoperating Vibration Operating 60g, 11ms, half sine 0. 25g, 5-500 Hz 1/2 octave/min sweep, 1 hour duration Nonoperating 1. 00g, 5-500 Hz 1/2 octave/min sweep, 1 hour duration --------------------------------------------------------------------------Maximum Altitude (unpressurized): Operating 10, 000 ft 3, 658m Nonoperating 30, 000 ft 12, 192m =========================================================================== Chapter 6. 2 VGA Display =========================================================================== U. S. Metric =========================================================================== Dimensions Height 4. 82 in 122. 4 mm/12. 24 cm Width 6. 42 in 163. 2 mm/16. 32 cm --------------------------------------------------------------------------Diagonal Size 8. 03 in 20. 4 cm --------------------------------------------------------------------------Mounting Internal --------------------------------------------------------------------------Display MSTN Backlit LCD --------------------------------------------------------------------------Gray Scales 16 High Resolution (640 x 480) 64 Low Resolution (340 x 200) --------------------------------------------------------------------------Brightness/Contrast Adjustable --------------------------------------------------------------------------Maximum Pixel Resolution 640 x 480 --------------------------------------------------------------------------Character Display 80 x 25 --------------------------------------------------------------------------Frequency: Horizontal 31. 2 KHz (CRT mode) 32 KHz (LCD mode) Vertical 125 Hz (60 VGA/70 CGA) --------------------------------------------------------------------------Display Inverter Board: Operating Voltage (Backlight) +5. 1V, +9V , +18. 7V Operating Output Voltage 310 Vrms Maximum Input Power 1. 8W Maximum Output Power 1. 25 Wrms =========================================================================== Table 6-3. [. . . ]