User manual HP DESIGNJET 5000

[. . . ] HP DesignJet 5000 Series Large-Format Printers Service Manual For HP Internal Use Only Copyright Hewlett-Packard Company 2000 This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HewlettPackard Company. First Edition, August 2000 Second Edition, January 2001 Warranty WARNING WARNING The Warning symbol calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a Warning symbol until the indicated conditions are fully understood and met. The information contained in this The procedures described in this document is subject to change manual are to be performed by without notice. [. . . ] Press the Load/ Unload Media button (see the User's Guide for detailed information on loading media). NOTE Do NOT use any other type of media apart from HP High Gloss Photo Paper. ACCURACY Load media for calibration 4. The Printer will start to print the Accuracy Calibration Pattern and the following message will be displayed on the front panel: ACCURACY Calibrating Below is a sample of the pattern printed. 5. Once the Accuracy Calibration Pattern is completed, the following message will be displayed. Select "Measure Pattern" and press Enter to automatically start the Load/Unload Media procedure. Top Recalibrate Back Create Pattern Measure Pattern Enter Make Selection Press Enter HP DesignJet 5000 Series Printers Service Manual 5-15 Service Calibrations 6. The Printer will unload the media and request you to remove it from the Printer. Press Enter to continue. Top Roll Unloaded. Remove Media. Back Enter Press Enter to coninue Press Enter 7. Press Load/Unload Media to start the load procedure for the printed sheet. Load/Unload Media Top ACCURACY Press Load/Unload key to load printed sheet Back Enter Press Load/Unload Media 8. When loading, rotate the pattern so that the edge with the arrows points to the leading edge, and then reload the pattern with the arrow edge print facing down. The Printer will load the pattern and then measure the alignment marks using the Line Sensor on the Carriage Assembly. The following message will be displayed while the Printer measures the pattern: ACCURACY Measuring 9. Once the calibration is completed, the following message will be displayed. Press Enter to return to the Accuracy Calibration menu. Top Calibration done Back Press Enter to continue Enter Press Enter 5-16 HP DesignJet 5000 Series Printers Service Manual Service Calibrations If the Calibration fails the following message is displayed. Press Enter to continue. Top ACCURACY Calibration Error (xxxx) Press ENTER to continue Back Enter Press Enter NOTE Refer to 5-26, Calibration Error Codes to troubleshoot error codes. HP DesignJet 5000 Series Printers Service Manual 5-17 Service Calibrations Carriage Height Calibration The purpose of this Service Calibration is to adjust the distance between the Carriage Assembly and the Center Platen. This calibration is necessary in order to prevent problems like Printhead crashes. Perform the Carriage Height Calibration whenever: n Carriage Assembly is disassembled or replaced. n Center Platen is disassembled or replaced. Perform the Carriage Height Calibration as follows: NOTE The procedure should be carried out using the Carriage Height Tool (See Figure 1 below) that came with the new Carriage Assembly or Center Platen Assembly. Carriage Height Tool Figure 1: 5-18 HP DesignJet 5000 Series Printers Service Manual Service Calibrations NOTE During the Carriage Height Calibration procedure the Carriage Assembly has to be moved along the length of the Printer for correct calibration. Make sure that the Carriage Assembly is only ever moved by pulling the Belt and never by direct contact with the Carriage itself (See Figure 2 below). Correct: move using the Belt. Incorrect: never move using Carriage Assembly. Figure 2: 1. Remove the Top Cover - Refer to Page 8-5. Remove the Back Cover - Refer to Page 8-23. Remove the Top EMC Cover - Refer to Page 8-32. [. . . ] content of the drawing, while maintaining Paper-axis its relative dimensions. The vertical axis, as you look at the printer ISO size from the front. An international standard media size; e. g. A programming ISS language that controls jobs going to a printer. [. . . ]