User manual HP EW5000

[. . . ] hp digital media receiver user's guide Contents welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 getting started. . . . . . . . . . . . . . . . . . . . . . . 3 unpacking the box . 8 sharing content . . . . . . . . . . . . . . . . . . . 13 server software . 13 14 14 15 15 16 16 17 17 18 18 19 19 20 20 21 controlling your receiver. . . . . . . . 9 menu basics . 12 playing music . . . . . . . . . . . . . . . . . . . . . . 23 music jukebox . [. . . ] To change the view order, press the options button while viewing a photo album. Select Change View and then choose your viewing order preference. rotating photos You can use the media receiver to rotate photos for proper viewing on your TV. Press the options button and select Rotate Photo 3. Rotate the photo 90 degrees left or right, or 180 degrees if the photo is upside down. The photo will be rotated for viewing. organizing your photos Photos are organized by the folder directory they appear in, and by their filename. To create a photo album, create a folder in the shared directory on your computer. Copy your photos into the new folder and your album is complete. For more help with organizing your photos, see "organizing photo albums" on page 19. 34 hp digital media receiver 7 network setup running the setup wizard Running the setup wizard is the easiest way to configure your network settings. The setup wizard runs the first time you power up your hp digital media receiver. You can run the setup wizard again at any time if your network settings need to be changed. From the home screen, press the options button and then select Run Setup Wizard from the menu. Alternatively, press the options button and select Network Setup to manually configure your network settings. The following sections describe the possible network setup options. cable attaches to the media receiver, and the other end attaches to your PC, a hub, or a router. Note: See the "glossary" on page 49 for a list of common network terms. To determine the proper network setup of your media receiver, you will need to know what kind of wired network you have. do you have a network? If you have a single PC and you connect to the internet with a phone line, chances are you do not have a network. At a minimum, you will need a network interface card (NIC) for your PC, or a USB-to-802. 11b dongle. You can then attach the media receiver to your PC. See "wired with cross-over cable" on page 39. If you have a single PC and you connect to the internet with a cable or DSL modem, check your modem connection. If the modem has only one network jack, you still don't have a network. You will need to user's guide preparing for wired setup In a wired network, you attach the media receiver to your network with a network cable. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Hardware Quality Engineering Manager Cupertino, CA, USA October, 2002 For Regulatory Compliance Information ONLY, contact: Hardware Quality Engineering Manager Hewlett-Packard, CPC 10500 Ridgeview Ct. Cupertino, CA 95015-4010 USA Phone: 408-343-5000 conforms to the following Product Specifications: Radio: 60 hp digital media receiver Operating Specifications Electrical ratings: Models: 5000 series 100-127 V/200-240 V, 4/2 A, 50/60 Hz 5° to 35° C -40° to 70° C 15 to 80% @ 26° C 90% @ 65° C (non-condensing) 0-2286 m 0-4572 m FCC Regulatory and Safety Information (USA only) Federal Communications Commission (FCC) Radio Frequency Interference Statement Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]