User manual HP IPAQ H5100

[. . . ] User's Guide hp iPAQ Pocket PC h5100 and h5500 series Document Part Number: 304926-001 May 2003 Note: Model shown in illustrations is iPAQ Pocket PC h5500 Series © 2003 Hewlett-Packard Development Company, L. P. HP, Hewlett Packard, and the Hewlett-Packard logo are trademarks of Hewlett-Packard Company in the U. S. iPAQ is a trademark of Hewlett-Packard Development Company, L. P. Microsoft, Windows, the Windows logo, Outlook, and ActiveSync are trademarks of Microsoft Corporation in the U. S. [. . . ] Select Allow other devices to connect, then All devices. Tap OK. Ä CAUTION: This allows any device, even those unknown to you, to connect to your iPAQ Pocket PC. After they are connected, security settings for specific services apply as specified in the Bluetooth Settings. User's Guide 8­7 Using Bluetooth Allowing Paired Devices to Connect Paired devices share and exchange an internally generated Link Key before connecting. The Link Key is derived from a unique Bluetooth device address, a random number, and a user-defined password. This feature allows only devices that you trust to connect to your iPAQ Pocket PC. From the Today screen, tap the Bluetooth icon > Bluetooth Settings > Accessibility tab. Select Allow other devices to connect, then Paired devices only. Tap OK. Allowing Others to Locate Your Device You can allow other devices to search and locate your iPAQ Pocket PC. device's address, that device If another remote device has your to you even though you did not may be able to locate and connect select for your device to be discovered. To allow others to locate your device: 1. From the Today screen, tap the Bluetooth icon > Bluetooth Settings > Accessibility tab. Tap OK to save the changes. User's Guide 8­8 Using Bluetooth Enabling Bluetooth Services You can select to enable certain services: Automatically when Bluetooth is activated When you permit the connection When a passkey or link key is correctly entered You can use any of these security options when transferring files, creating a serial port connection, exchanging business card information, configuring dial-up networking, and joining a personal network. Automatically Enabling Services You can allow devices to connect without any authorization so that any time Bluetooth is on, it is ready for connections. From the Today screen, tap the Bluetooth icon > Bluetooth Settings. Tap the tab for the service you want to enable: File Transfer, Information Exchange, Serial Port, Personal Network Server, or Audio Gateway. Ensure there are no check marks in the Authorization required or Authentication (Passkey) required checkboxes. Tap OK. User's Guide 8­9 Using Bluetooth Requiring Authorization to Access Services If you elect to require authorization to access services, you must authorize each connection. Then your iPAQ Pocket PC will always ask you if the connection should be permitted. To require authorization to access services: 1. From the Today screen, tap the Bluetooth icon > Bluetooth Settings. Tap the tab for the service you want to enable: File Transfer, Information Exchange, Serial Port, Personal Network Server, or Audio Gateway. Tap OK. Secure Connections using a Passkey or Bond To establish a secure connection with another device, you can use the passkey feature or an established bond. You can also add data encryption to this type of security. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio or television technician for help User's Guide A­1 Regulatory Notices Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for products marked with the FCC logo--United States only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ]