User manual HP JETDIRECT 600N PRINT SERVER JETDIRECT 600N PRINT SERVER HARDWARE INSTALLATION GUIDE - 5969-6858

[. . . ] For HP Printers with EIO Slots HP JetDirect 600N Hardware Installation Guide Hardware Installation Guide HP JetDirect 600N Print Server ©Copyright Hewlett-Packard Company 2000. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under the copyright laws. Warranty and Service For product warranty and service information, refer to the Quick Start Guide supplied with this product. A copy of the specific warranty terms applicable to your HP product and replacement parts can be obtained from your HP Sales and Service Office or Authorized dealer. Publication number 5969-3561 First Edition February 2000 Applicable Products: J3110A J3111A J3112A J3113A Safety Considerations Prior to the installation and use of this product, review all safety markings and instructions. If the product is marked with this symbol, refer to the product manuals to protect the product from damage. [. . . ] Press [Menu] repeatedly until EIO # JETDIRECT MENU is displayed (# identifies the EIO slot number of the card). Press [Item] until CFG NETWORK=NO* appears. NO* indicates that access to the EIO JetDirect network menus will be bypassed. You must change this to CFG NETWORK=YES* to access the EIO JetDirect menus: a. Press [Item] to scroll through each network protocol until the one you want to change is displayed. IPX/SPX=ON* DLC/LLC=ON* TCP/IP=ON* ETALK=ON* Note: ON* indicates the protocol is enabled. OFF* indicates the protocol is disabled. "ETALK" refers to the EtherTalk protocol (not available on Token Ring cards) G To change the protocol status, press [Value] 3 Control Panel Configuration and then press [Select]. G Press [Item] to continue to the next protocol. 5. To activate the printer and save your changes, press [Go]. Control Panel Configuration 3-3 Configuring IPX Frame Types On IPX/SPX protocol networks (for example, Novell NetWare), the format of network communication frames must be specified on the card. In most cases, you can keep the default Frame Type setting, which is AUTO ("Automatic"). However, you can manually set the frame type format if required. Note that the IPX/SPX protocol must be enabled (IPX/SPX=ON*) before you can configure frame types. IPX Frame Types on an HP JetDirect Ethernet Card Frame Type AUTO (default) EN_8023 EN_II EN_8022 EN_ SNAP Description Automatically senses and limits the frame type to the first one detected. Limits the frame type to IPX over IEEE 802. 3 frames. All others will be counted and discarded. Limits the frame type to IPX over Ethernet Frames. All others will be counted and discarded. Limits the frame type to IPX over IEEE 802. 2 with IEEE 802. 3 frames. All others will be counted and discarded. Limits the frame type to IPX over SNAP with IEEE 802. 3 frames. All others will be counted and discarded. IPX Frame Types on an HP JetDirect Token Ring Card Frame Type AUTO (default) TR_8022 Description Automatically senses and limits the frame type to the first one detected. Limits the frame type to IPX over IEEE 802. 2 LLC with IEEE 802. 5 frames. All others will be counted and discarded. Limits the frame type to IPX over SNAP with IEEE 802. 5 frames. [. . . ] 1996-98 Class A (Korea) (*For EU immunity compliance, see the Declaration of Conformity on page B-3. ) Regulatory Statements FCC Statements General Information. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pursuant to Part 15. 21 of the FCC Rules, any changes or modifications to this equipment not expressly approved by the Hewlett-Packard Company may cause interference and void the FCC authorization to operate this equipment. [. . . ]