User manual HP L1502E FLAT PANEL MONITOR

[. . . ] hp L1520 D5063 15-inch LCD monitor (15-inch viewable image) user's guide www. hp. com/go/monitorsupport Notice Important Safety Instructions What the L1520 Monitor Offers Setting Up the Monitor Removing your monitor's pedestal How to Install the Drivers Adjusting the Monitor Using the Monitor Troubleshooting LCD Monitor Quality and Pixel Policy Technical Specifications Care and Cleaning Environmental Information Agency Regulatory Notices hp L1520 15-inch LCD Monitor (15-inch Viewable Image) User's Guide Notice Notice The information contained in the documents accompanying this product is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. HP shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] 2 When the screen is in the vertical position you want, press the Menu button to exit the setting screen. 26 English Using the Monitor Mode Recall Using Mode Recall restores the original default settings for Color, Brightness, Phase, and Clock. If you make manual adjustments that are unsatisfactory, you can use this function to restore the original settings. To use Mode Recall 1 Open the Mode Recall setting screen. See "Using the On-Screen Display Manager (OSD)" on page 19. A window with a red bar appears. 2 Press the Select button to proceed with Mode Recall, or press the Menu button to exit without resetting. 3 If you reset with Mode Recall, press the Menu button to exit the setting screen. English 27 Using the Monitor Backlight Info The Backlight Info window shows the elapsed time of usage for the light behind the display screen. The expected lifespan of the backlight is approximately 30, 000 to 40, 000 hours. At some point after the maximum usage time of the backlight has been exceeded, you may notice a decrease in brightness of up to 50%. At this point, the backlight needs to be replaced to restore full brightness. WARNING: The backlight can be replaced only by a trained technician. Please contact the HP Support Center for assistance. Do not attempt to replace the light yourself. NOTE: Do not use a screen saver with the LCD monitor, as the backlight will be used. It is recommended that you enable an automatic power saving mode on the PC, or switch off the monitor when not in use. To view Backlight Info: 1 Open the Backlight Info setting screen. See "Using the On-Screen Display Manager (OSD)" on page 19. 2 Press the Menu button to exit the setting screen. Serial Number You may need to provide the display serial number to HP Support technicians to help them serve you better during a support call. To view a Serial Number: 1 Open the Serial Number setting screen. See "Using the On-Screen Display Manager (OSD)" on page 19. 2 Press the Menu button to exit the setting screen. 28 English Using the Monitor Mode Info The Mode Info screen shows whether the current video input mode is analog (1) or digital (2); shows the current resolution and refresh rate; and shows how many User settings you have changed, and how many preset settings have not been changed. To view Mode Info: 1 Open the Mode Info setting screen. See "Using the On-Screen Display Manager (OSD)" on page 19. The Video Input mode, the resolution and refresh rate, and the number of Preset and User values are displayed. 2 Select the Preset or User values with the Browse buttons. [. . . ] CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e. g. increased risks of skin cancer (malignant melanoma) as a consequence. English 43 Agency Regulatory Notices Lead:*2* Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO '99 requirement permits the inclusion of lead since no replacement has yet been developed. 1* Bio-accumulative is defined as substances which accumulate within living organisms. [. . . ]