User manual HP L1506 15-INCH LCD MONITOR

[. . . ] User Guide 1506, 1706 and1906 LCD Monitors Document Part Number: 389521-002 October 2005 This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. Enhanced for Accessibility © 2005 Hewlett-Packard Development Company, L. P. HP, Hewlett Packard, and the Hewlett-Packard logo are trademarks of Hewlett-Packard Company in the U. S. Compaq and the Compaq logo are trademarks of Hewlett-Packard Development Company, L. P. Microsoft, Windows, and the Windows logo are trademarks of Microsoft Corporation in the U. S. [. . . ] The following table provides the menus and their functions at each level: Advanced OSD Menu Levels Level 2 Level 3 Adjustment Scale Adjustment Scale Auto Adjustment Horizontal Position Vertical Position Clock Clock Phase Cancel Save and Return Color 9300 K 6500 K Custom Color sRGB Cancel Save and Return Language Deutsch English Espanol Francais Italiano Nederlands Simplified Chinese Cancel Save and Return Management Power Saver Power On Recall On / Off Selection On / Off Selection N N N Custom Color Adjustment Y "Adjusting" Message Adjustment Scale Adjustment Scale Adjustment Scale Adjustment Scale Level 1 Brightness Contrast Image Control Factory Preset Y Y Y Y Y Y Y User Guide 4­7 Operating the Monitor Advanced OSD Menu Levels (Continued) Level 1 Level 2 Level 3 Factory Preset Mode Display Power-On Status Display Sleep Timer Serial Number Basic Menu Cancel Save and Return OSD Control Horizontal Position Vertical Position OSD Timeout Cancel Save and Return Information Factory Reset Exit Yes No Adjustment Scale Adjustment Scale Adjustment Scale N N N On / Off Selection On / Off Selection Timer Set Menu Displays monitor serial number N N N Adjusting Screen Quality Allow the monitor to warm up for 20 minutes before performing the following procedures. The Auto-adjustment feature automatically fine-tunes the image quality each time a new video mode is displayed. If additional image quality improvement is desired, run the Auto-Adjust software on the CD and press the ­ (Minus) button on the monitor front panel to manually activate the Auto-Adjustment function. 4­8 User Guide Operating the Monitor For more precise adjustments, run the Adjustment Pattern provided on the CD and use the Clock and Clock Phase controls (accessible from the OSD menu) as described in the following section. Optimizing Digital Conversion This monitor contains advanced circuitry that allows the flat panel screen to function like a standard monitor. Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock Phase. Use these controls only when the auto-adjust function does not provide a satisfactory image. set correctly since the Clock The Clock must first beon the main Clock setting. Phase settings are dependent Clock--Increase/decrease the value to minimize any vertical bars or stripes visible on the screen background. Clock Phase--Increase/decrease the value to minimize video distortion or video jitter. will obtain the best When using the controls, youapplication providedresults by using the Auto-Adjustment pattern on the CD. the Clock and Clock Phase monitor When adjusting distorted, continue adjustingvalues, if theuntil the images become the values distortion disappears. To restore the factory settings, select Yes from the Factory Reset menu in the on-screen display. User Guide 4­9 Operating the Monitor Identifying Monitor Conditions Special messages will appear on the monitor screen when identifying the following monitor conditions: Input Signal Out of Range-- Indicates the monitor does not support the input signal because the resolution and/or refresh rate are set higher than the monitor supports. For 15" monitors, set the resolution and refresh rate to 1024 x 768 at 60 Hz. For 17" and 19" monitors, set the resolution and refresh rate for 1280 x 1024 at 60 Hz. Restart your computer for the new settings to take effect. Monitor Going to Sleep-- Indicates the screen display is entering a sleep mode. Check Video Cable-- Indicates the video cable is not properly connected to the computer. OSD Lock--The OSD can be enabled or disabled by pressing and holding the Menu button on the front panel for 10 seconds. If the OSD is locked, the warning message "OSD Lock" displays for ten seconds. If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD. If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD. Sleep Timer Mode The Sleep Timer mode is an energy-saving feature that enables you to set a time for the monitor to power on and off at the same time every day. This also extends the life of the backlight bulbs in the monitor. The Sleep Timer has five settings: Set Current Time Set Sleep Time 4­10 User Guide Operating the Monitor Set On Time Timer: On/Off Sleep Now To set the timer: 1. Press the Menu button on the monitor front panel to display the Advanced Menu. Press the Menu button to select Management. Scroll down and highlight and select Sleep Timer > Set Current Time. local time before reset the for You must setorthe current Note that the timeyoudisplayed time24 Sleep Time On Time. Press the Menu button once to enter the adjustment mode for hours. Press the - (Minus) or + (Plus) buttons to adjust the hour. Press the Menu button again to enter the time for minutes. [. . . ] Lead in the solder and some component leads. Disposal of this material can be regulated because of environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (EIA) (www. eiae. org). Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union Regulatory Notice This product complies with the following EU Directives: Low Voltage Directive 73/23/EEC EMC Directive 89/336/EEC User Guide C­3 Agency Regulatory Notices Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) which are listed on the EU Declaration of Conformity issued by Hewlett-Packard for this product or product family. This compliance is indicated by the following conformity marking placed on the product: Disposal of Waste Equipment by Users in Private Household in the European Union This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. [. . . ]