User manual HP L2335 LCD FLAT PANEL MONITOR

[. . . ] Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Å Ä WARNING: Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. [. . . ] You may need it later if you move or ship your monitor. 2­4 www. hp. com User's Guide 3 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and other attached devices, then follow these steps: 1. Place the monitor in a convenient, well-ventilated location near your computer. Connect one end of the monitor signal cable to the video connector on the rear panel of the computer, and the other end to the back of the monitor. with The DVI-D cable supplied Your this monitor is for digitalto-digital connection only. computer must have a DVI-compatible graphics card installed for use with this cable. When connecting the DVI-D signal cable to the DVI connector on the monitor, you must connect the other end of the DVI-D cable to the DVI connector on the computer. User's Guide www. hp. com 3­1 Setting Up the Monitor 3. Connect the power cable to the back of the monitor, and the other end of the power cable to an electrical wall outlet. 3­2 www. hp. com User's Guide Setting Up the Monitor 4. Adjust the monitor as needed for your comfort using the monitor's tilt, swivel, and height adjustment capabilities. User's Guide www. hp. com 3­3 Setting Up the Monitor 3­4 www. hp. com User's Guide Setting Up the Monitor Å CAUTION: To reduce the risk of electric shock or damage to your equipment: Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Disconnect power from the monitor by unplugging the power cord from the electrical outlet. Going to Sleep--Indicates the monitor is entering the sleep mode. Check Video Cable--Indicates the video cable may not be plugged into the computer or monitor, or that the computer may not be turned on. No Input Signal--Indicates the monitor is not receiving a video signal from the PC. Check to see if the PC is off or in the power saving mode. Adjusting Screen Quality Allow the monitor to warm up for 20 minutes before performing the following procedures. The Auto Adjustment feature automatically fine-tunes the image quality each time a new video mode is utilized. If additional improvement is desired, select the Auto button on the front bezel. For more precise adjustments, use the adjustment pattern provided on the CD-ROM, and adjust the clock and phase settings (accessed from the OSD menu) as described in the following section. 4­8 www. hp. com User's Guide Operating the Monitor Optimizing Digital Conversion This monitor contains advanced circuitry that allows the flat panel screen to function like a standard monitor. Two controls in the on-screen display can be adjusted to improve image performance: Clock and Clock Phase. Use these controls only when the auto adjust function does not provide a satisfactory image. set correctly since the Clock The Clock must first beon the main Clock setting. Phase settings are dependent Clock--Increase/decrease the value to minimize any vertical bars or stripes visible on the screen background. [. . . ] energy saver feature only works The above that have energy saver features. when connected to computers By selecting settings in the monitor's Energy Saver utility, you can also program the monitor to enter into the reduced power state at a predetermined time. When the monitor's Energy Saver utility causes the monitor to enter the reduced power state, the Power light blinks amber. User's Guide www. hp. com B­5 C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]