User manual HP L5006TM TOUCHSCREEN MONITOR

[. . . ] User Guide HP L5006tm 15" Touchscreen Monitor Document Part Number: 419998-001 May 2006 This guide provides information on setting up the monitor, installing drivers, using the on-screen display menu, troubleshooting and technical specifications. Enhanced for Accessibility © Copyright 2006 Hewlett-Packard Development Company, L. P. The information contained herein is subject to change without notice. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U. S. Adobe, Acrobat, and Acrobat Reader are trademarks or registered trademarks of Adobe Systems Incorporated. [. . . ] To access the OSD, do the following: 4­4 User Guide Operating the Monitor 1. Press the Menu button on the side panel to activate the OSD menu. Use the or controls to move clockwise or counterclockwise through the menu. Press the Enter key on the keyboard, the parameter will be highlighted when selected. To quit the OSD screen at any time during the operation, press the Menu button. If the OSD remains untouched for a short period of time, the OSD automatically disappears. will disappear if no input activities are detected for OSD Menu Table The following table lists the On-Screen Display (OSD) menu selections and their functional descriptions. OSD Menu Icon OSD Control Description Brightness Increases or decreases brightness. Contrast Increases or decreases contrast. H-Position Adjusts the position of the screen image left and right. Adjusts the position of the screen image up and down V-Position User Guide 4­5 Operating the Monitor OSD Menu Icon OSD Control Description Phase Increases or decreases the snow noise or the image after auto-adjustment is made. Clock The dot clock is fine-adjusted after auto adjust. Moves the OSD position horizontally on the screen. When the button is pressed, the OSD menu will move to the right side of the screen. Likewise, when the button is pressed, the OSD control menu will move to the left side. Moves the OSD position vertically on the screen. When the button is pressed, the OSD menu will move to the top side of the screen. Likewise, when the button is pressed, the OSD control menu will move to the lower side. Press or to select 9300, 6500, 5500, 7500 or USER. Only when selecting USER can you make adjustments to the R/G/B (red/green/blue) content. Press Enter to restore the factory default setting. The Auto-Adjustment will automatically adjust V-Position, H-Position, Clock and Clock-Phase. Returns the monitor to its default settings. OSD H-Position OSD V-Position Color Balance Auto-Adjustment Recall Defaults 4­6 User Guide Operating the Monitor OSD Menu Icon OSD Control Description OSD Language Selects from English, French, German, Spanish and Japanese. Information Description Indicates the current resolution, H-Frequency and V-Frequency. the Clock and Clock Phase monitor When adjusting distorted, continue adjustingvalues, if theuntil the images become the values distortion disappears. To restore the factory settings, select the Recall Defaults menu in the on-screen display. Identifying Monitor Conditions Special messages will appear on the monitor screen when identifying the following monitor conditions: Out of Range-- Indicates the monitor does not support the input signal because the resolution and/or refresh rate are set higher than the monitor supports. No Input Signal-- Indicates the monitor is not receiving a video signal from the PC on the monitor video input connector. Check to determine if the PC or input signal source is off or in the power saving mode. Check Video Cable-- Indicates the video cable is not properly connected to the computer. User Guide 4­7 Operating the Monitor Power Management System The monitor is equipped with the power management function which automatically reduces the power consumption when not in use. [. . . ] Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call (281) 514-3333 C­2 User Guide Agency Regulatory Notices To identify this product, refer to the Part, Series, or Model number found on the product. Materials Disposal This HP product contains Mercury in the fluorescent lamp in the display LCD that might require special handling at end-of-life. Disposal of this material can be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities or the Electronic Industries Alliance (EIA) (www. eiae. org). Canadian Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis Canadien Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Power Cord Set Requirements The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100-120V or 200-240V. [. . . ]