User manual HP LASERJET 2000 LASERJET, COLOR LASERJET AND LASERJET MFP AND ALL-IN-ONES - WINDOWS 98, 98 SECO

[. . . ] Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Part number Q2660-90937 Edition 1, 10/2003 FCC Requirements (United States) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] If you do not know whether the outlet is grounded, check with a qualified electrician. Do not touch the contacts on the end of any of the sockets on the HP LaserJet 3380 allin-one. Unplug this device from wall outlets before cleaning. Do not install or use this device near water or when you are wet. Install the device securely on a stable surface. Install the device in a protected location where no one can step on or trip over the power cord and the power cord will not be damaged. If the device does not operate normally, see the electronic User Guide. Refer all servicing questions to qualified personnel. Hewlett-Packard Development Company, L. P. 249 Houston, TX 77070 Hewlett-Packard Development Company, L. P. 249 Houston, TX 77070 Table of contents 1 Introduction Device overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Preparing the location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Press the bottom of the faceplate onto the device, and then continue to press while pushing your hands up toward the top of the faceplate until it snaps into place. Note Make sure that the faceplate is aligned correctly and is not pressing any buttons. The control panel includes the following controls: 1. scan controls 14 Chapter 2 Setting up your device ENWW Installing the input trays 1. Slide the trays in and down at an angle until they fit securely. Remove any shipping tape inside and outside of the trays. 3. Place the media in the media input tray, and then adjust the media guides until they are flush with the media. ENWW Installing the input trays 15 Note Do not fan the media before placing it in the tray. Install the priority input tray on top of the media input tray. Installing the automatic document feeder (ADF) input tray 1. Align the two tabs on the input tray with the two grooves in the ADF lid. Slide the tray into the grooves until the tray snaps into place. 16 Chapter 2 Setting up your device ENWW Installing the print cartridge 1. Make sure that the print-cartridge door is open. 2. Remove the print cartridge from its packaging, and then shake the cartridge gently five or six times. [. . . ] If you are connecting the device to a network, see "Connecting to a network". If you are connecting the device directly to a computer, see "Connecting to a computer". If you are using all of the device functionality, see the Fax Guide to set up the fax, and then see "Connecting to a network" (network connection) or "Connecting to a computer" (computer connection) in this Start Guide. 24 Chapter 2 Setting up your device ENWW Connecting to a network If you want to connect the device to a network, see the instructions that are included with the HP print server (which is not included with the HP LaserJet all-in-one). After completing the instructions, see "Connecting to a computer". Connecting to a computer Note To install the software for Macintosh, see "Installing the Macintosh software (OS 9. x to OS X)". [. . . ]