User manual HP LASERJET 3055 ALL-IN-ONE

[. . . ] HP LaserJet 3050/3052/3055/3390/3392 All-in-One User Guide HP LaserJet 3050/3052/3055/3390/3392 All-in-One User Guide Copyright and License © 2006 Copyright Hewlett-Packard Development Company, LP Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. The information contained in this document is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. [. . . ] CAUTION Do not load paper that is heavier than 105 g/m2 (28 lb bond). This could lead to a jam in the all-in-one. Open the printer driver (see Gaining access to the printer drivers). For Windows, on the Finishing tab, click Print on Both Sides. The product is now ready to print on both sides of the paper. To print on both sides manually (HP LaserJet 3050/3052/3055 all-in-one) NOTE The printer driver also contains instructions and graphics for manually duplexing. In the software program, open the all-in-one properties (printer driver). On the Finishing tab, select Print on Both Sides. NOTE If the Print on Both Sides option is dimmed or unavailable, open the all-in-one properties (printer driver). On the Device Settings tab or the Configure tab, select Allow Manual Duplexing, and then click OK. Print the document. ENWW Print: How do I? 197 4. After one side has been printed, remove the remaining media from the input tray, and set it aside until after you finish your manual duplexing job. HP LaserJet 3050 HP LaserJet 3052/3055 5. Gather the printed pages, keep the printed side facing down, and straighten the stack. HP LaserJet 3050 HP LaserJet 3052/3055 6. Place the stack of media in the input tray again. The printed side should be facing down with the top edge feeding into the all-in-one first. 1 HP LaserJet 3050 HP LaserJet 3052/3055 7. On the computer screen, click OK and wait for the second side to print. 198 Chapter 11 How do I? ENWW To print on both sides manually (HP LaserJet 3390/3392 all-in-one) 1. Insert enough paper into one of the trays to accommodate the print job. If you are loading special paper such as letterhead, load it in one of the following ways: For tray 1, load the letterhead paper with the front side up, bottom-edge first. For all other trays, load letterhead paper with front side down, and the top edge at the back of the tray. CAUTION Do not load paper that is heavier than 105 g/m2 (28 lb bond). Open the printer driver (see Gaining access to the printer drivers). On the Finishing tab, select Print on Both Sides (manually). Remove any blank paper that is in tray 1. Insert the printed stack into the tray that is specified on the control panel. Load the paper with the printed side up, and the bottom-edge feeding into the all-in-one first. Follow the instructions in the pop-up window that appears before feeding the output stack back for printing the second half of the job. A prompt might appear on the control-panel display that instructs you to press a button to continue. 7. ENWW Print: How do I? 199 Print on both sides (Macintosh) Automatic two-sided printing (duplexing) is available by using the automatic duplexer on the HP LaserJet 3390/3392 all-in-one. [. . . ] shared line The sharpness of an image, measured in dots per inch (dpi). The higher the dpi, the greater the A single telephone line that is used for both voice and fax calls. surge protector A device that protects a power supply and communications lines from electrical surges. 396 Glossary ENWW TWAIN An industry standard for scanners and software. By using a TWAIN-compliant scanner with a TWAINcompliant program, a scan can be initiated from within the program. URL Uniform resource locator, the global address of documents and resources on the Internet. [. . . ]