User manual HP LASERJET 5MP SUPPLEMENT GUIDE

[. . . ] Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws. Warranty The information contained in this document is subject to change without notice. Electrical Shock Hazard To avoid electrical shock, use only supplied power Hewlett-Packard makes cords and connect only to no warranty of any kind properly grounded (3-hole) with regard to this mate- wall outlets. rial , including , but not limited to , the implied warranties or merchantability and fitness for a particular purpose. [. . . ] Power Requirements Power Consumption (typical for HP LaserJet 5P and HP LaserJet 5MP) 100/120V (+/- 10%) 50/60Hz (+/- 2Hz) 127 Volts NOM During printing - 165 W (average) During standby ­ 5W (instant power save) During power save mode - 5 W Minimum recommended circuit capacity 4 Amps 220/240V (+/- 10%) 50 Hz (+/- 2Hz) During printing - 165 W (average) During standby ­ 5W (instant power save) During power save mode - 5 W 1. Power Requirements Power Consumption (typical for 6P and 6MP) 100/120V (+/- 10%) 50/60Hz (+/- 2Hz) 127 Volts NOM During printing ­ 175 W (average) During standby ­ 8 W (instant power save) During power save mode ­ 8 W Minimum recommended circuit capacity 5 Amps 220/240V (+/- 10%) 50/60 Hz (+/- 2Hz) During printing ­ 175 W (average) During standby ­ 8 W (instant power save) During power save mode ­ 8 W 2. Make sure there is adequate space for: · Opening top cover (A) · You can order the documents listed below. And extensions across the printer family supporting PJL and PCL 5. HP LaserJet Family Quick Service Reference Guide 5010-6395 * This item must be ordered through HP Parts Direct Ordering, (800) 227-8164. The following table lists the software that is shipped with each printer. However, some simple functions are also available from the status panel. You also receive status information about the operation of the IrDA-compatible infrared (IR) port from the status light just above the port (for more information, see "To Print Using the Infrared Port, " later in this appendix). DATA status light READY status light GO button IR port status light RESET button ERROR status light TRAY 1 status light TRAY 2 status light The Status Panel consists of two buttons for completing tasks and six lights that indicate the status of the printer (see Figure 5). The status lights for Tray 1 and Tray 2 have been moved from top status panel down to the front of the printer. These status lights are now located next to the trays. GO button TRAY 1 (top) status light TRAY 2 empty light IR (bottom) status light JOB CANCEL button ERROR (back) light DATA (middle) light READY (front) light The Status Panel consists of two buttons for completing tasks and six lights that indicate the status of the printer (see Figure 6). Prints a self-test page when pressed simultaneously with the rESET button (JOB CANCEL button on the 6P/6MP. The printer must be in Ready Mode (the green Ready light on steady). ⷠPrints unprinted data in the printer's memory (the Ready and Data lights are both on steady). The top status panel lights will cycle while the printer memory is being cleared, and then return to a ready state (front light on). This may take a while, depending on the size of the print job. If JOB CANCEL is pushed when the printer is idle, the top panel status lights will cycle, but nothing else will happen. There are six Status Panel lights on the printer: · These lights indicate the current status of the printer by displaying an amber or a green hue and flashing individually or sequentially as a group (cascading). ERROR (amber) Indicates an error condition, such as a paper jam, missing toner cartridge, or the printer's top cover is open. dATA (green) When the Data light is on , the printer is printing. When the Ready light and the Data light are both on, the printer still has unprinted data in its memory. [. . . ] Then, position the device within the range of operation, and print the job again. If the Data light is on, press the RESET/JOB CANCEL button to clear the printer's memory. Then, position the device within the range of operation, and print the job again. The IR status light turns off during transmission. [. . . ]