User manual HP MULTI-SITE TRAFFIC DIRECTOR SA9200

[. . . ] hp multi-site traffic director server appliance sa9200 user guide ©Copyright 2001 Hewlett-Packard Company. Hewlett-Packard Company 3000 Hanover Street Palo Alto, CA 94304-1185 Publication Number 5971-0897 March 2001 Disclaimer The information contained in this document is subject to change without notice. HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. Warranty A copy of the specific warranty terms applicable to your Hewlett-Packard products and replacement parts can be obtained from http://www. hp. com/serverappliances/support. [. . . ] Syntax: config sys snmp sysContact <string> where string is a string of displayable characters. Config Sys SNMP Commands 99 CHAPTER 6 HP Multi-Site Traffic Director Server Appliance SA9200 User Guide Command sysLocation Description Allows you to specify a value for the MIB-II variable sysLocation. Syntax: config sys snmp sysLocation <system location> where system location is a string of displayable characters. sysName Allows you to specify a value for the MIB-II variable sysName. The default is the hostname of the SA9200. Syntax: config sys snmp sysName <system name> where system location is a string of displayable characters. community info Displays the community strings the SA9200 is configured to accept, such as Community (name), IP address, and Rights. Rights are ro (read-only) and rw (read-write). Specifies community strings that the SA9200 accepts on incoming SNMP requests. Up to 10 community strings can be created. Syntax: config sys snmp community create <string> ip [<IP address>|any] rights [ro|rw] community create where string is the name of the community you wish to create, ip address is the IP address of the host from which you accept this community string. If any is specified, the community string is accepted on requests from any IP address. ro means the community string has read-only privilege. rw means the community string has read-write privilege. The default community strings are public any ro and private any rw. community delete Deletes a community string that the SA9200 can accept on incoming SNMP requests. Syntax: config sys snmp community delete <string> ip [<ip address> | any] where: string is the name of the community string you wish to delete, and ip address is the IP address of the host from which you do not accept this community string. If any is specified, the community string does not accept requests from any IP address. Config Sys SNMP Commands 100 CHAPTER 6 System Commands Command trap info Description Displays the trap receiver list of: · · Trap ID Address Trap Community trap port Specifies the trap port number. The port number is between 5020 and 65535. Syntax: config sys snmp trap port <trap port> where trap port is the designated number. trap create Allows you to specify the host to which SA9200 sends SNMP traps. By default the trap receiver list is empty, that is, no traps are sent. Syntax: config sys snmp trap create <ip address> community <community string> where ip address is the IP address of the host to which you wish to send SNMP traps. community string is sent with all traps sent to the IP address. trap delete Deletes a host from the trap receiver list. Syntax: config sys snmp trap delete <ip address> community <community string> where ip address is the IP address of the host you wish to delete from the trap receiver list, and community string is an identifier associated with specified access rights. [. . . ] A service is an application protocol that is offered on a network. The device where the service is running is identified by an IP address. A port is used to identify the protocol at the designated IP address. Services contain an IP address and a port. [. . . ]