User manual HP OMNIBOOK 900

[. . . ] HP OmniBook Docking System User's Guide 1-1 Notice This manual and any examples contained herein are provided "as is" and are subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. shall not be liable for any errors or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or the examples herein. Consumer transactions in Australia and the United Kingdom: The above disclaimers and limitations shall not apply to Consumer transactions in Australia and the United Kingdom and shall not affect the statutory rights of Consumers. [. . . ] · Install and remove plug-in modules. There is a module adapter for each OmniBook model supported by the dock. The module bay adapter must be purchased separately. To use the plug-in modules for your OmniBook, install the module adapter for that OmniBook. For information on module bay adapters, see your reseller or the HP OmniBook website at www. hp. com/omnibook. For more information on plug-in modules, refer to the manual that accompanied the plug-in modules, the OmniBook Reference Guide, or the HP OmniBook website. 1-39 Installing Accessories Using the Module Bay Adapter To install the module bay adapter WARNING 8S EZSMH VMWO SJ IPIGXVMGEP WLSGO VIQSZI XLI TS[IV GSVH JVSQ XLI TS[IV SYXPIX FIJSVI VIQSZMRK XLI XST GSZIV SJ XLI HSGO %PWS VIQSZI ER] RIX[SVO GSRRIGXMSRW ERH HMWGSRRIGX ER] I\XIVREP HIZMGIW %P[E]W VITPEGI XLI XST GSZIV SJ XLI HSGO FIJSVI XYVRMRK XLI HSGO SR EKEMR Important You will need a medium-sized Phillips screwdriver to install your module adapter. 1. Disconnect all cables connected to the rear of the dock. Disconnect the power cord from the dock. Remove the Kensington lock, if attached. Remove the five screws securing the top cover to the base. 1-40 Installing Accessories Using the Module Bay Adapter 7. Slide the top cover toward the back of the dock about 1 cm (1/2 inch). CAUTION: 0MJXMRK XLI XST GSZIV [MXLSYX WPMHMRK MX FEGO [MPP HEQEKI XLI HSGO 8. Fold the top cover back until it lies flat on the work surface. Be careful not to pull any cable connectors loose. 1-41 Installing Accessories Using the Module Bay Adapter 9. Remove the cover plate from the module bay slot by pressing down on the two tabs and pushing it out. . 10. Remove and save the locking screw from the module bay housing. Insert the module adapter for your OmniBook plug-in modules into the module bay until it locks in place. 12. Re-install the locking screw in the hole in the top of the module bay housing to secure the module adapter in the bay. This screw prevents removal of the module adapter from the dock. 1-42 Installing Accessories Using the Module Bay Adapter 13. Connect IDE cable 2, audio cable 2, and power cable 2 to the connectors protruding from the back of the module bay housing. 14. Carefully place the top cover of the dock onto the base of the dock about 1 cm (1/2 inch) back from the front of the base and slide the top cover forward until the five screw holes are properly aligned. 1-43 Installing Accessories Using the Module Bay Adapter 15. Reinstall the five screws you removed previously. You have completed installation of the module adapter. To replace a plug-in module Important Install only IDE devices such as a CD-ROM drive, LS-120 drive, or DVD drive in the module bay. The module bay does not support non-IDE devices such as floppy disk drives or batteries. [. . . ] Input: 100 to 240 Vac (50 to 60 Hz), 2. 5A. Kensington lock slot secures dock , OmniBook, PC cards, PCI boards, and plug-in modules. Power Security Size (without mointor stand) Height: Depth: Width: Weight 130. 0 mm (5. 13 in. ). kg (17. 4 lb). Environmental Operating temperature: Storage temperature: Relative humidity: Major ICs 5 to 35 °C (41 to 95 °F). ­20 to 50 °C (­4 to 122 °F). [. . . ]