User manual HP PAVILION 17 INCH CRT MONITORS

[. . . ] User's Guide Color Monitor Series v72 © 2003 Hewlett-Packard Development Company, L. P. HP, Hewlett-Packard, and the Hewlett-Packard logo are trademarks of Hewlett-Packard Company in the U. S. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U. S. Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel Corporation in the U. S. [. . . ] Press the Select button on the monitor choose the function. Press the Right-Adjustment or Left-Adjustment buttons to increase (Right) or decrease (Left) the level of adjustment. Press Select to save the new adjustment. To exit the On-Screen Display, select the Exit icon and press the Select button once. 4­6 User's Guide Operation On-Screen Display Functions Use the Right-Adjustment and Left-Adjustment buttons found on the front control panel of your monitor to adjust these functions. Icon On-Screen Display Icons and Functions Function Description Contrast Right-Adjustment increases the contrast and Left-Adjustment decreases the contrast. Right-Adjustment increases the brightness and Left-Adjustment decreases the brightness. Right-Adjustment moves the image to the right and Left-Adjustment moves the image to the left. Right-Adjustment increases the horizontal size and Left-Adjustment decreases the horizontal size. Right-Adjustment moves the image up and Left-Adjustment moves the image down. Right-Adjustment increases the vertical size and Left-Adjustment decreases the vertical size. Right-Adjustment makes the image sides convex and Left-Adjustment makes the image concave. Right-Adjustment adjusts the image so the top is larger and Left-Adjustment adjusts the image so that the bottom is larger. Right-Adjustment moves the top and bottom of the image to the right and Left-Adjustment moves the top and bottom of the image to the left. Brightness Horizontal Position Horizontal Size Vertical Position Vertical Size Pincushion Trapezoid Pin Balance User's Guide 4­7 Operation On-Screen Display Icons and Functions (Continued) Icon Function Description Parallelogram Tilt (Rotation) Degauss This control corrects the tilted vertical edges of the image on both sides of the screen that are in the same direction. Right-Adjustment tilts the sides of the image to the right and Left-Adjustment tilts the sides of the image to the left. This control demagnetizes the screen to reduce color impurities. Hewlett-Packard suggests you not degauss more than once within a 30-minute period of time. Right-Adjustment selects the color temperature to the right and Left-Adjustment selects the color temperature to the left. This control resets the monitor to factory default values. Color Temp Reset Exit This control exits the OSD menu. 4­8 User's Guide Operation Monitor Messages No Signal Message If a "No Signal" message displays on your monitor, check to be sure your video cable is properly connected and ensure that your computer is powered on. User's Guide 4­9 Operation Out of Frequency Range Message If an "Out of Frequency Range" message displays on your monitor, your video resolution and/or refresh rate are set higher than the levels your monitor supports. To change the video resolution or refresh rate on your monitor, follow these steps: 1. Refer to your computer's operating system Help for instructions on entering Safe Mode. Change your display settings to a supported setting (see "Technical Specifications" on page B­1). Restart your computer so that the new settings take effect. 4­10 User's Guide Operation Using the Energy Saver Mode Your monitor is designed to meet strict Environmental Protection Agency (EPA) Energy Star® requirements for reduced power consumption. [. . . ] The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco. se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www. tco-info. com Environmental Requirements Flame Retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. [. . . ]