User manual HP PAVILION DV9000 NOTEBOOK PC

[. . . ] Maintenance and Service Guide HP Pavilion dv9000 Notebook PC Document Part Number: 417615-002 September 2006 This guide is a troubleshooting reference used for maintaining and servicing the computer. It provides comprehensive information on identifying computer features, components, and spare parts; troubleshooting computer problems; and performing computer disassembly procedures. © Copyright 2006 Hewlett-Packard Development Company, L. P. registered trademarks of Microsoft Corporation. Intel and Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. [. . . ] incorrect installation module Removing a Memory Module Reverse the above procedure to install a memory module. 5­14 Maintenance and Service Guide Removal and Replacement Procedures 5. 7 RTC Battery RTC Battery Spare Part Number Information RTC battery (includes 2-sided tape) 431436-001 1. Prepare the computer for disassembly (refer to Section 5. 3). Remove the memory module compartment cover (Section 5. 6). Disconnect the RTC battery cable 1 from the system board. RTC battery is secured the by 2-sided Thereplacement RTC batterytosparecomputer include tape. All part kits 2-sided tape. Removing the RTC Battery Reverse the above procedure to install the RTC battery. Maintenance and Service Guide 5­15 Removal and Replacement Procedures 5. 8 Mini Card Module Mini Card Module Spare Part Number Information For use only with models using Intel processors: 802. 11a/b/g WLAN Mini Card module for use in the MOW1 countries listed below: Antigua & Barbuda Argentina Australia Bahamas Barbados Canada Chile Dominican Republic Guam Guatemala Panama India Indonesia Malaysia Mexico New Zealand 407674-001 Paraguay Saudi Arabia Taiwan The United States Vietnam 407674-002 The Netherlands Norway Oman Slovenia South Africa Spain Sri Lanka Sweden Switzerland Turkey The United Kingdom Uzbekistan 802. 11a/b/g WLAN Mini Card module for use in the MOW2 countries listed below: Aruba Austria Azerbaijan Bahrain Belgium Bermuda Bulgaria Cayman Islands Columbia Croatia Cyprus The Czech Republic Denmark Egypt El Salvador Estonia Finland France Georgia Germany Greece Hungary Iceland Ireland Italy Latvia Lebanon The Philippines Poland Portugal Romania Russia Serbia and Montenegro Singapore Slovakia Liechtenstein Lithuania Luxembourg Malta Monaco 5­16 Maintenance and Service Guide Removal and Replacement Procedures Mini Card Module Spare Part Number Information (Continued) 802. 11a/b/g WLAN Mini Card module for use in the ROW countries listed below: China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea 407674-003 Uruguay Venezuela For use only with models using AMD processors: 802. 11a/b/g WLAN Mini Card module for use in the United States and Canada. 802. 11a/b/g WLAN Mini Card module for use in the countries listed below: China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea 407160-001 407160-002 Uruguay Venezuela 407159-001 407159-002 Uruguay Venezuela 802. 11b/g WLAN Mini Card module for use in the United States and Canada. 802. 11b/g WLAN Mini Card module for use in the countries listed below: China Ecuador Haiti Honduras Pakistan Peru Qatar South Korea 1. Prepare the computer for disassembly (Section 5. 3). Remove the memory module compartment cover (Section 5. 6). Maintenance and Service Guide 5­17 Removal and Replacement Procedures 3. Make note of which wireless antenna cable is attached to which antenna clip on the Mini Card module before disconnecting the cables. Then disconnect the cables 1 from the module. Remove the two Phillips PM2. 0×11. 0 screws 2 that secure the Mini Card module to the computer. (The edge of the module opposite the socket rises away from the computer). Remove the module 3 by pulling it away from the socket at an angle. modules to prevent Mini Cardinstallationare designed with a notch 4 socket. incorrect into the Mini Card module Removing a Mini Card Module Reverse the above procedure to install a Mini Card module. 5­18 Maintenance and Service Guide Removal and Replacement Procedures 5. 9 Optical Drive Optical Drive Spare Part Number Information For use only with computer models using Intel processors: DVD/CD-RW Combo Drive For use only with computer models using AMD processors: DVD/CD-RW Combo Drive For use with all computer models DVD±RW/R and CD-RW Double-Layer Combo Drive with LightScribe DVD±RW/R and CD-RW Double-Layer Combo Drive 432973-001 432972-001 432971-001 434673-001 1. Prepare the computer for disassembly (Section 5. 3). Maintenance and Service Guide 5­19 Removal and Replacement Procedures 2. Remove the Phillips PM2. 5×8. 0 screw 1 that secures the optical drive to the computer. Insert a thin tool, such as a paper clip 2, into the media tray release hole. (The optical drive media tray releases from the optical drive. ) 4. Use the media tray frame to slide the optical drive 3 out of the computer. [. . . ] Recycle the backlight and LCD panel. C­14 Maintenance and Service Guide D Connector Pin Assignments Table D-1 Universal Serial Bus Pin 1 2 Signal +5 VDC Data ­ Pin 3 4 Signal Data + Ground Maintenance and Service Guide D­1 Connector Pin Assignments Table D-2 RJ-45 (Network) Pin 1 2 3 4 Signal Transmit + Transmit ­ Receive + Unused Pin 5 6 7 8 Signal Unused Receive ­ Unused Unused D­2 Maintenance and Service Guide Connector Pin Assignments Table D-3 S-Video-Out Pin 1 2 3 4 Signal TV-Ground TV-CVBS TV-Ground TV-Ground Pin 5 6 7 Signal TV-CD TV-Ground TV-YD Maintenance and Service Guide D­3 Connector Pin Assignments Table D-4 External Monitor Pin 1 2 3 4 5 6 7 8 Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog Pin 9 10 11 12 13 14 15 Signal +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock D­4 Maintenance and Service Guide Connector Pin Assignments Table D-5 RJ-11 (Modem) Pin 1 2 3 Signal Unused Tip Ring Pin 4 5 6 Signal Unused Unused Unused Maintenance and Service Guide D­5 Connector Pin Assignments Table D-6 Audio-In (Microphone) Pin 1 2 Signal Audio signal in Audio signal in Pin 3 Signal Ground Table D-7 Audio-Out (Headphone) Pin 1 2 Signal Audio out, left channel Audio out, right channel Pin 3 Signal Ground D­6 Maintenance and Service Guide E Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the computer meets the requirements for use in the country where the equipment is purchased. Power cord sets for use in other countries must meet the requirements of the country where the computer is used. Maintenance and Service Guide E­1 Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries. The length of the power cord set must be at least 1. 5 m (5. 0 ft) and a maximum of 2. 0 m (6. 5 ft). All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used. [. . . ]