User manual HP PHOTOSMART C5100 ALL-IN-ONE SETUP GUIDE

[. . . ] You can adjust the height of the display to a position suitable for viewing. 3 Locate components HP Photosmart C5100 All-in-One series Basics Guide Windows CD Basics Guide 4 x 6 in (10 x 15 cm) photo paper USB cable* *Purchased separately Mac CD adapter control panel faceplate (may be pre-attached) Ethernet cable* *Purchased separately Documentation CD This CD may be included for some languages where help is not available through the software. power cord The contents of your box may differ Additional network equipment specified later in the guide. ink cartridges HP Photosmart C5100 All-in-One series Setup Guide 4 a Attach the control panel faceplate (if not attached) b a Position the control panel faceplate over the buttons on the device. b Press down firmly on all edges of th overlay to secure it. Make sure all buttons are visible and not blocked. 5 Main tray: a Load paper into both trays b c d Load plain white paper in the bottom paper tray. Photo paper tray: e f g e Lift the output tray. f Pull out the photo tray. g Load the 4 x 6 inch (10 x 15 cm photo paper from the sample pac with the glossy side down in the photo tray. h i Tip: If the paper is tabbed, make sure the tab is towards you. 2 · HP All-in-One 6 Connect the power cord and adapter USB cable users: Do not connect the USB cable until instructed later in this guide. 7 Press the On button After you press the On button, wait for the prompt on the color graphics display before continuing. 8 Open the access door a b HP All-in-One · 3 9 a Lift latches inside of the device a Squeeze the bottom of each latch to release it, and then lift the latch. [. . . ] For an Ethernet cable connection, go to Section B (page 9) for instructions. 6 · HP All-in-One Section A: USB Connection A1 Choose the correct CD Mac Users: Note: If the startup screen does not appear, doubleclick My Computer, double-click the CDROM icon with the HP logo, and then double-click setup. exe. Windows Users: a Insert the HP All-in-One Windows CD. b Follow the onscreen instructions to install the software. c On the Connection Type screen, make sure to select directly to this computer. d Continue to the next page. a Locate the HP All-in-One Mac CD. b Continue to the next page. HP All-in-One · 7 A2 Connect the USB cable Mac Users: a Connect the USB cable from your computer to the USB port on the back of the device. Windows Users: a Follow the onscreen instructions until you see the prompt to connect the USB cable. (This may take several minutes. ) Once the prompt appears, connect the USB cable to the port on the back of the HP All-in-One, and then to any USB port on your computer. b Double-click the HP All-in-One Installer icon. c Make sure you complete all screens, including the Setup Assistant. b Follow the onscreen instructions to complete the software installation. A3 Go to step 16 at the back of this setup guide 8 · HP All-in-One Section B: Ethernet (wired) network B1 a Connect the Ethernet cable a Locate the Ethernet cable that you purchased separately. b Remove the yellow plug from the back of the device. c Connect one end of the Ethernet cable to the Ethernet port on the back of the device. d Connect the other end of the Ethernet cable to the hub/router switch. e Continue to the next page. Important: Do not connect the Ethernet cable to a cable modem b You must have a working network. If you already connected the USB cable, do not connect the Ethernet cable. c HP All-in-One · 9 B2 Choose the correct CD Mac Users: Note: If the startup screen does not appear, doubleclick My Computer, doubleclick the CD-ROM icon with the HP logo, and then double-click setup. exe. b Double-click the HP All-in-One installer icon. Windows Users: a Insert the HP All-in-One Windows CD. c On the Connection Type screen, make sure to select through the network. Follow the onscreen instructions. c Make sure you complete all screens, including the Setup Assistant. To install software on additional computers, go to step 14. d You must unlock or accept all firewall messages by clicking Next on any screen that refers to a firewall. To install software on additional computers, go to step 14. Questions: Anti-virus, Anti-Spyware, or firewall programs can block software installation. For details, go to www. hp. com/support, enter Photosmart C5100, and then search for Firewalls. B3 Go to step 16 at the back of this setup guide 10 · HP All-in-One 14 Install software on additional computers If you have additional computers on your network, install the HP All-in-One software on each computer. [. . . ] The Photosmart Express menu appears on the color graphics display. The most recent photo on your memory card appears on the display. c c Press the arrow buttons to select a different picture, then press OK. d d Keep pressing Okay to print your photo. If you are looking at a photo on the display, you can quickly print a 4 x 6 inch (10 x 15 cm) photo by pressing the Print Photos button. The HP All-in-One makes a print of the photo on your memory card. [. . . ]