User manual HP PL4245N

[. . . ] HP PL4245N 42" HD-Ready Plasma TV User's Guide The information in this document is subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. HP shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO ANY MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT OR SERVICE TO YOU. [. . . ] Refer to your S-video source owner's manual for information about your equipment's video output requirements. Connecting a Component (YPbPr or YCbCr) Source Use YPbPr cables to connect your component video source or other equipment to the component input connectors (YPbPr or YCbCr) on the TV. To make these connections: 1 Turn off the TV and the component input source equipment. 2 Connect one end of the red, green, and blue component cables to the YPbPr or YCbCr video output connector on the component video source, and connect the other ends to the YPbPr or YCbCr inputs on the back of the TV. 3 Connect the red and white audio cables from your video source to the Audio In on the back of the TV. Be careful to keep the audio right and left channel connections correct for stereo sound. 4 Turn on the TV and the component video source. Insert media into the component video source and play it. 5 Select YPbPr1, YPbPr2, or YCbCr as the input source for the main TV picture (so you see the image playing from the component video source) by using the front panel buttons or press the YPbPr or YCbCr button on the TV remote control. Refer to "Selecting the input source" on page 21. 6 To set up the TV remote control to operate the component video source, refer to "Programming the remote control for component control" on page 33. Refer to your component video source owner's manual for information about your equipment's video output requirements. Connecting the HP Media Center PC You can connect the TV to an HP Media Center PC (HP MCPC) and use the special buttons on the remote control associated with the HP MCPC. Refer to your HP MCPC documentation to connect the TV to the HP MCPC as: · A monitor using either a VGA cable or a DVI-D cable. · A TV using the TV input source connectors for video (composite) inputs, S-video, or component video inputs; see the appropriate procedure in this document. Setup 17 Using the HP MCPC with the TV remote control 1 Turn on the TV and the HP MCPC. 2 Press the appropriate TV input source button on the TV remote control to display the image on the main picture (refer to "Selecting the input source" on page 21): · Choose the DVI/VGA button when you've connected the TV to the HP MCPC as a monitor using the DVI-D or VGA connectors. or S-video inputs. · Choose the AV button when you've connected the TV to the HP MCPC as a TV using the Video · Choose the YPbPr or YCbCr button when you've connected the TV to the HP MCPC as a TV using the Component Video inputs. 3 Press HP. PC button on the remote control to select the HP MCPC as the controlled device. Point the remote control at the HP MCPC remote control sensor and press the buttons you want to use. The remote control buttons, such as the guide, channel, volume, and cursor buttons, function along with the special HP MCPC buttons described in the table. TV Remote Button YCbCr, YPbPr, AV, or DVI/VGA HP. PC HP. MC Back (EXIT) Enter PIP Input Replay/Reverse Skip/Forward HP MCPC Button Function Selects the TV input source for the main screen. Selects the HP MCPC as the device controlled by the remote control. Start Back OK Record Replay Skip Installing or Replacing Remote Control Batteries When the batteries are low, the red light on the remote control blinks twice when a button is pushed. Insert two AA non-rechargeable batteries into the remote control ensuring that you place them with the proper polarity. 1 Press and open the cover on the back of the remote control. [. . . ] · The backlight may have reached the end of its service life. · Make sure the remote control is within operating range. · Check that there are no obstacles between the remote control and the sensor window on the display. The picture is not clear. The picture is light or improperly tinted. The remote control does not work. The picture is not sharp. · The reception may be weak. [. . . ]