User manual HP PROLIANT DL380 G4 STORAGE SERVER PROLIANT DL380 G4 STORAGE SERVER INSTALLATION GUIDE (WSS R2 VERSION, MARCH 2006

[. . . ] HP ProLiant DL380 G4 Storage Server installation guide This guide provides installation and configuration information for the HP ProLiant DL380 G4 Storage Server with Microsoft® Windows® Storage Server 2003 R2. 5697-5670 Part number: 5697-5670 First edition: March 2006 Legal and notice information © Copyright 2006 Hewlett-Packard Development Company, L. P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright. [. . . ] Connecting the power cord also restores the storage server to whatever previous powered state it was last in. This could result in the server powering up, the fans operating, and the power indicator coming on. NOTE: The keyboard, mouse, and monitor are used only for the "Direct attach method" on page 31. They are not provided with your storage server. 26 Installing the server Powering on the server Power on the server after connecting the cables. Power on server by pushing the I/O button (1). The power LED located on the I/O button illuminates. 1 5058 Figure 6 Power on button 2. Insert the HP ProLiant Storage Server System Installation and Recovery DVD into the storage server disk drive to finalize the operating system installation and updates. IMPORTANT: To successfully complete the installation and update process, you must run the HP ProLiant Storage Server System Installation and Recovery DVD. If you have not inserted this DVD into the disk drive when you boot the server, you will be prompted to do so. Follow the steps below to complete the server installation. If the following screen comes up on your PC, click Exit and reboot or hold the power I/O button for 10 seconds. HP ProLiant DL380 G4 Storage Server installation guide 27 Figure 7 Finalize installation screen 28 Installing the server 4. During reboot, you see the screen below. The storage server performs the following actions: · Restore image. · Boot Windows and finalize setup. Figure 8 Restore progress screen CAUTION: Do not interrupt the reboot sequence; it takes a considerable amount of time. By now you should have determined the access method for your storage server. For more information, see "Planning for installation" on page 15. Go to "Accessing the HP Storage Server Management console" on page 31 to set up server access. HP ProLiant DL380 G4 Storage Server installation guide 29 30 Installing the server 3 Accessing the HP Storage Server Management console Before accessing the HP Storage Server Management console, verify that the storage server is completely installed in the rack, and that all cables and cords are connected. See the HP ProLiant 2U Rail installation instructions for additional installation guidance. To access the HP Storage Server Management console, you can use these access methods: Direct attach Remote browser To connect directly to the storage server without using the network. To establish a browser-based connection to the HP ProLiant Storage Server Management console from a remote client running Internet Explorer 5. 5 (or later). To establish a connection from a remote client without using a browser. This method requires the client to have Windows remote desktop capability. To establish a browser-based connection from a remote client using the iLO interface. [. . . ] Same as above. Subnet mask Default gateway Local area connection 2 IP address Subnet mask Default gateway 40 Configuring the server on the network Configuration Worksheet DNS server A Domain Name System (DNS) server name is required to provide for domain name to IP address resolution. A Windows Internet Naming Service (WINS) server name is required to determine the IP address associated with a particular network computer. WINS server Server Name Server name Assign a unique name to the storage server. This name identifies the storage server on the network. HP ProLiant DL380 G4 Storage Server installation guide 41 Running the Rapid Startup Wizard The Rapid Startup Wizard is only displayed during the initial setup process. This wizard guides you through the configuration process. Figure 11 Rapid Startup Wizard The Rapid Startup Wizard guides you through configuring the following system settings: · Date, time, and time zone · Administrator Identity (user name and password) · Alert e-mail notification · Integrated Lights-Out (iLO) settings · Simple Network Management Protocol (SNMP) Settings · Network Interfaces · Server Name For more information about the configuration settings available in the Rapid Startup Wizard, click Help to see the corresponding Rapid Startup Wizard online help topic. 42 Configuring the server on the network 5 Complete system configuration Additional configuration tasks The physical installation and basic configuration for the HP ProLiant storage server is complete. [. . . ]