User manual HP PROLIANT XW25P BLADE WORKSTATION

[. . . ] HP ROM-Based Setup Utility User Guide Revised to include HP ProLiant Generation 5 servers and BL server blades Part Number 347563-006 January 2007 (Sixth Edition) © Copyright 2003-2007 Hewlett-Packard Development Company, L. P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting and additional warranty. [. . . ] The Set Admin Password option is a simple character string with a maximum of seven characters. To disable or clear the password, enter the password followed by a / (slash) when prompted to enter the password. Network Server Mode The Network Server Mode option is a toggle setting that sets the server to operate in network server mode. This feature works in conjunction with the power-on password. When set to Disabled, the server operates normally. When it is set to Enabled, the following actions occur: · · · The local keyboard remains locked until the power-on password is entered. The power-on password prompt is bypassed. When a diskette is in the diskette drive, the server does not start unless the power-on password is entered locally. IMPORTANT: Network server mode cannot be enabled until the power-on password has been established. QuickLock The QuickLock option is a toggle setting that either enables or disables the QuickLock feature. When set to Enabled, the keyboard is locked by pressing the Ctrl+Alt+L keys. The keyboard remains locked until the power-on password is typed. NOTE: If the power-on password is disabled at the power-on key prompt, the QuickLock feature remains inactive until the password is changed in RBSU. RBSU menu 21 BIOS Serial Console/EMS Support IMPORTANT: Some languages or characters may require a specific emulation mode. The BIOS Serial Console/EMS Support option configures the serial port to view POST error messages and run RBSU remotely through a serial connection to the server COM port. The remote server does not require a keyboard or mouse. For details about using BIOS Serial Console, refer to the HP BIOS Serial Console User Guide (http://www. hp. com/servers/smartstart). BIOS Serial Console design supports VT100+ protocol, and ANSI and V100 terminal emulation. VT100 is supported by all terminal emulation programs. However, ANSI supports enhanced graphics and is more aesthetically appealing. ANSI is the recommended choice if it meets the system requirements. CLI support is available on some new servers for faster, more compatible display when configuring a server using VT100 emulation. For more information, see "Command Line Interface Overview (on page 42). " When viewed in BIOS Serial Console, the RBSU main menu looks slightly different from the local server view. The following menu options are available: · · · · BIOS Serial Console Port BIOS Serial Console Baud Rate EMS Console BIOS Interface Mode BIOS Serial Console Port The BIOS Serial Console Port option provides additional selections for enabling BIOS Serial Console. RBSU menu 22 Selecting the Enable Remote option without the supported RILOE II or iLO firmware will result in an error: The setting Enable Remote requires RILOE-II or iLO with firmware version 1. 20 or greater (1. 41 or greater with iLO firmware recommended). Do not use the Enable Remote setting if iLO is Disabled and RILOE-II is not installed. BIOS Serial Console Baud Rate The BIOS Serial Console Baud Rate option enables baud rate changes. RBSU menu 23 EMS Console The EMS Console option is a Microsoft® Windows ServerTM 2003 feature that allows for emergency management console to be redirected through the serial port. [. . . ] Sets POST Custom text to string specified by <string>. System Maintenance CLI Commands Command HELP EXIT RBSU INSPECT PXE MEMDIAG CPUDIAG DISKDIAG Usage HELP or HELP <command> EXIT RBSU INSPECT PXE MEMDIAG CPUDIAG DISKDIAG Description Displays all supported commands or usage and descriptions of a specific command. (Diagnostics Utility has CLI output as well. ) Executes Diagnostics Utility specified. (Diagnostics Utility has CLI output as well. ) Executes Diagnostics Utility specified. (Diagnostics Utility has CLI output as well. ) Command Buffering Support The CLI mode support buffers the previous five commands entered from the command line, accessible using the up arrow key and the down arrow key. Additional CLI support The CLI mode support automatically handles output to the screen that scrolls off the screen by implementing a -More- prompt at the bottom of the screen and waiting for user input to scroll to the next page of data using key commands. [. . . ]