User manual HP S7500MM CRT MONITOR REFERENCE GUIDE - CRT MONITORS 5500, V72, MX704, 7500, 7550, 9500 - ENHANCED FO

[. . . ] Reference Guide CRT Monitors 5500, v72, mx704, 7500, 7550, 9500 Document Part Number: 346224-002 January 2004 This guide provides information on setting up the monitor, installing drivers, using the onscreen display menu, troubleshooting, regulatory notices, and technical specifications. Enhanced for accessibility. © Copyright 2004 Hewlett-Packard Development Company, L. P. The information contained herein is subject to change without notice. Microsoft, MS-DOS, Windows, and Windows NT are trademarks of Microsoft Corporation in the U. S. [. . . ] Never disconnect the monitor by pulling the cord. Turn off your monitor off when not in use. You can substantially increase the life of your monitor by using a screen saver program and turing off the monitor when not in use. Unplug your monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. If the screen requires additional cleaning, use an antistatic CRT screen cleaner. CAUTION: Do not use benzene, thinner, ammonia, or any other volatile substances to clean your monitor or the screen. These chemicals may damage the cabinet finish as well as the screen. Slots and opening in the cabinet are provided for ventilation. These openings must not be blocked or covered. Never push objects of any kind into cabinet slots or other openings. Do not place plants on top of your monitor. Water or dirt from the plant may get into the vents. Do not drop your monior or place it on an unstable surface. Do not all anything to rest on the power cord. Keep your monitor in a well ventilated area, away from excessive light, heat, or moisture. Keep your monitor away from high-capacity transformers, electical motors, and other devices with strong magnetic fields. In a two-monior system, place your monitors as far apart from one another as possible to lessen interference between them. Reference Guide 2-3 Safety and Maintenance Guidelines Do not place the monitor face down. Damage could result to the front panel controls or the monitor screen. Removing the Monitor Base In the event that you need to disassemble the base from the monitor, follow these instructions: 1. If you must remove the base attachment, release the catch and slide the base toward the back of your monitor. Lift the base up and away from your monitor. 2-4 Reference Guide 3 Installation Attaching the Monitor Base On some monitors, the base must be attached prior to setting up the monitor. Align the hooks on the base with the sockets on the bottom of the monitor and attach the base. Reference Guide 3-1 Installation 2. Push the base toward the front of the monitor until it stops. Setting Up the Monitor Before setting up the monitor, place it in a convenient, wellventilated location near your computer. Turn off the power to your computer and other peripheral devices. [. . . ] TTL Separate 15-pin D-sub connector 100 to 240V AC 50 +3 to 60 +3 Hz 30 amps @ 120V 60 amps @ 220V 130 W (Max. ) Reference Guide B-11 Technical Specifications Dimension (W x H x D) Unpacked w/attached base Weight Operating Temperature Storage Temperature Humidity Altitude TCO Requirements MPRII Plug and Play 17. 9 x 18. 5 x 18. 7 inches (maximum) 455 x 470 x 475 mm (maximum) 44 lb Max. 50o F to 95o F 10o C to 35o C -22o F to 140o F -30o C to 60o C 20% to 80% (non-condensing) Up to 10, 000 ft. /3048 meters Select models meet TCO'99 or TCO'03 Select models meet MPRII Yes B-12 Reference Guide C Agency Regulatory Notices Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]