User manual HP STORAGEWORKS 7410 VIRTUAL ARRAY STORAGEWORKS VIRTUAL ARRAY 7000 FAMILY INSTALLATION AND UPGRADE INSTRUCTIONS FO

[. . . ] The GBIC then plugs into the HOST FC connector on the array controller. into the DISK FC and HOST FC connectors on VA 7400/7410 array controllers. LC connectors (Figure 3) are small form factor connectors that plug directly Both SC and LC connectors are keyed to install only one way. 2 Installation & Upgrade Instructions Figure 2 Removing & Replacing a Fiber Optic Cable & GBIC (VA 7100 Array Controller) 2 1 3 Figure 3 Removing & Replacing Fiber Optic Cables (VA 7110/7400/7410 Array Controller) 2 1 Installation & Upgrade Instructions 3 Gigabit Interface Converters (VA 7100 Array Controller Only) Removing a GBIC 1 Remove the fiber optic cable. 2 Push in the GBIC tabs and gently pull the GBIC out of the HOST FC slot. Replacing a GBIC 1 Remove the GBIC cover. 2 With even pressure, gently push the GBIC into the HOST FC connector until it clicks into place. [. . . ] 3 VA 7100 only: Slide the latch (Figure 6, 1) all the way to the left. 4 VA 7100: Press down the lock (Figure 6, 2) and pull out the cam lever (3). VA 7400/7410/7110: Pull out the cam lever (Figure 7, 2). 5 Grasp the edges of the array controller with both hands and push it firmly into the slot. (Figure 6 or Figure 7). 8 Installation & Upgrade Instructions 6 Push in the cam lever (Figure 6, 3 or Figure 7, 2) until it clicks into place. 7 VA 7100 only: Slide the latch (Figure 6, 1) all the way to the right. 8 VA 7400/7410/7110 only: Tighten the cam lever screw (Figure 7, 1). 9 VA 7100 only: Replace the GBIC (Figure 2, 3). 10 Replace the fiber optic cables (see Figure 2 or Figure 3). Note If you need to change the default Fibre Channel Loop ID on the array controller, use the following VFP command: vfpmgr -L <loop id> -c <array controller card number> Note The following step is only required if an HP-UX host is connected to the array using one of the following FC HBAs: A5158A, A6684A, A6685A, or A6795A. 11 From the HP-UX host, run the following command to allow the driver to use the new controller in the path: /opt/fcms/bin/fcmsutil device_file replace_dsk remote-NPort-ID Note A reboot of the host will also allow the driver to see the new controller. However, using the fcmsutil command is a much easier and quicker method of accomplishing this. If you do not run the fcmsutil command, errors similar to the following will appear in syslog: Unable to access previously accessed device at nport ID 0x2a. 'World-wide name' (unique identifier) for device at nport ID 0x2a has changed. If the device has been replaced intentionally, please use the fcmsutil(1M) command's replace_dsk option to allow the new device to be used. Fibre Channel Driver detected a parse error in the FLOGI/ PLOGI response returned by nport ID 0x2a. FLOGI/PLOGI Fail Code = 0x6. Installation & Upgrade Instructions 9 Figure 6 Removing & Installing a VA 7100 Controller 1 2 3 4 10 Installation & Upgrade Instructions Figure 7 Removing & Installing a VA 7110/7400/7410 Array Controller 1 2 3 Installation & Upgrade Instructions 11 Array Controller Filler Panels Removing an Array Controller Filler Panel Caution Do not operate the array for more than 5 minutes with a controller or filler panel removed. Either a controller or filler panel must be installed in the slot to maintain proper airflow. 1 Loosen the cam lever screws (Figure 8, 1) with a T-10 driver or flat-blade screwdriver. 2 Pull out both cam levers (2) at the same time. 3 Pull the controller filler panel (3) out of the slot. Installing an Array Controller Filler Panel 1 Pull out both cam levers (Figure 8, 2) at the same time. 2 Push the controller filler panel (3) firmly into the slot. 3 Push in both cam levers at the same time. 4 Tighten the cam lever screws (1). 12 Installation & Upgrade Instructions Figure 8 Removing & Installing an Array Controller Filler Panel 1 2 3 Installation & Upgrade Instructions 13 Array Controller Batteries Caution Make sure you observe the following precautions. -- Removing a battery may cause data loss. [. . . ] 7 Reinstall the battery on the controller. See "Installing an Array Controller Battery" on page 15. See "Installing an Array Controller" on page 8. 9 Repeat steps 4 - 8 for the other controller. [. . . ]