User manual HP STORAGEWORKS ENTERPRISE FILE SERVICES WAN ACCELERATOR

[. . . ] HP StorageWorks Enterprise File Services WAN Accelerator 2. 1 Management Console user guide *392359-002* *392359­002* Part number: 392359­002 Second edition: November 2005 Legal and notice information © Copyright 2005 Hewlett-Packard Development Company, L. P. © Copyright 2003­2005 Riverbed Technology, Inc. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. [. . . ] Type a new service group password in the Password and Confirm Password text boxes. The password is limited to 8 characters. Optionally, modify the priority number in the Priority text box to assign a priority to the service group. Optionally, modify the weight in the Weight text box to assign a redirection weight to the HP EFS WAN Accelerator. The range is 0-65535. 76 2 - CONFIGURING THE HP EFS WAN ACCELERATOR 6. Select either, gre or l2 from the Encapsulation Scheme drop-down list to redirect packets using Generic Routing Encapsulation (gre) or Layer-2 (l2) redirection. The either value uses Layer-2 first, then gre. 2 - CONFIGURING THE HP EFS WAN ACCELERATOR 7. Click Update Settings to apply your new settings to the running configuration. Under Flags, click Source IP Hash, Source Port Hash, Destination IP Hash, or Destination Port Hash to define the fields the router hashes on and if certain ports should be redirected. Click Update Flags to apply your new settings to the running configuration. Under Ports, click Ports Disabled, Use Source Ports or Use Destination Ports. If a source or destination is specified, the router redirects only that TCP traffic with the same source or destination ports specified in the Ports list. If you set a source or destination port, type the port number in the Add Port text box and click Add Port. You can add 7 ports. NOTE: For detailed information about hash table settings for WCCP, see the Cisco documentation Web site at http://www. cisco. com/univercd/home/home. htm. 12. Under Routers, type the IP address for the router in the Add Router IP text box and click Add Router to add additional routers to the service group. Click Save to write your settings to memory or click Reset to return the settings to their previous values. TIP: To remove ports, click the check box next to the port name and click Remove Selected Ports. This action applies the settings to the running configuration. Click Save to write your settings to memory or click Reset to return the settings to their previous values. TIP: To remove routers, click the check box next to the router IP address and click Remove Selected Router. This action applies the settings to the running configuration. Click Save to write your settings to memory or click Reset to return the settings to their previous values. HP STORAGEWORKS EFS WAN ACCELERATOR MANAGEMENT CONSOLE USER GUIDE 77 Setting Proxy File Service The following section describes how to set the Proxy File Service (PFS) for the HP EFS WAN Accelerator. It has the following sections: "Enabling PFS, " next "Setting PFS Share Parameters" on page 85 PFS requires an HP EFS WAN Accelerator, Model DL320-1010, DL320-2010, DL380-3010, or DL380-5010 to ensure adequate disk capacity. PFS supports only Windows 2000 and above domains. NOTE: The Setup: Proxy File Service - Configuration page only appears if you are running an HP EFS WAN Accelerator, Model DL320-1010, DL320-2010, DL380-3010, or DL3805010. [. . . ] Each router sends that portion of the routing table (keeps track of routes to particular network destinations) that describes the state of its own links. It also sends the complete routing structure (topography). A unit of information transmitted, as a whole, from one device to another on a network. A small utility program that is used to investigate, or test, the status of a system, network or web site. [. . . ]