User manual HP STORAGEWORKS ENTERPRISE MODULAR ARRAY HSG80 ACS SOLUTION SOFTWARE V8.6 FOR COMPAQ OPENVMS INSTALLATION AND CONFIGURATI

[. . . ] Compaq StorageWorks HSG80 ACS Solution Software Version 8. 6 for Compaq OpenVMS Installation and Configuration Guide First Edition (June 2001) Part Number: AA-RH4BD-TE Compaq Computer Corporation © 2001 Compaq Computer Corporation. Compaq, the Compaq logo, and StorageWorks Registered in U. S. Microsoft, MS-DOS, Windows, Windows NT, Windows 2000 are trademarks of Microsoft Corporation. All other product names mentioned herein may be trademarks of their respective companies. [. . . ] Enter client system notification options and the client system access options. For a definition of the client system notification options and the client system access options, see Table 4­3. Enter the name for a subsystem and the device name used to access the subsystem. You can enter more than one subsystem. If you want to monitor and manage a subsystem, you need to enter this information. The subsystem, which is comprised of the controller and its array of physical devices, must have access to the Agent system. Enter a password. It must be a text string that has 4 to 16 characters. It is entered from the client system to gain configuration access. Start the Agent. The Agent runs as a process in the background. When you start the Agent, you are instructing the software to start monitoring the subsystems. 4­10 HSG80 ACS Solution Software Version 8. 6 for Compaq OpenVMS Installation and Configuration Guide Reconfiguring the Agent You can change your configuration using the SWCC Command Console Agent Configuration menu by entering the following command: $ @sys$manager:swcc_config The following is an example of the Agent Configuration menu: SWCC Agent for HS* Controllers Configuration Menu Agent is enabled as TCP/IP Services for OpenVMS service. Agent is now: active Agent Admin Options: 1)Change Agent password 2)Agent Enable/Start 3)Agent Disable/Stop 4)Uninstall Agent Client Options: 5)Add a Client 6)Remove a Client 7)View Clients Storage Subsystem Options: 8)Add a subsystem 9)Remove a subsystem 10)View subsystems E)Exit configuration procedure CAUTION: After you make a change to the configuration, such as adding a client system, you must stop and then start the Agent for your changes take effect. When you stop and then start the Agent, the Storage Windows for the subsystems connected to the agent system lose their connection. To regain that connection, close and then reopen the Storage Windows connected to the agent system after you restart the Agent. Installing and Configuring the HS-Series Agent 4­11 Table 4­4 Information Needed to Configure Agent Term/Procedure Adding a Client system entry Description For a client system to receive updates from the Agent, you must add it to the Agent's list of client system entries. The Agent will only send information to client system entries that are on this list. In addition, adding a client system entry allows you to access the Agent system from the Navigation Tree on that Client system. You need to tell the Agent the subsystem that it needs to monitor. Network names for the computers on which the Client software runs. The access privilege level controls the Client system's level of access to the subsystems. 0=No Access-Can use the Client software to add a system to a Navigation Tree, set up a pager, and view properties of the controller and the system. You cannot use Client to open a Storage Window. 1=Show Level Access-Can use the Client software to open a Storage Window, but you cannot make modifications in that window. 2=Storage Subsystem Configuration Capability-Can use the Client software to make changes in a Storage Window to modify a subsystem configuration. Client system notification options Note: For all of the client system notification options, local notification is available through an entry in the system error log file and Email (provided that Email notification in PAGEMAIL. COM has not been disabled). 0 = No Error Notification-No error notification is provided over network. [. . . ] Upper Layer Protocol. Glossary­19 ULP process A function executing within a Fibre Channel node which conforms to the Upper Layer Protocol (ULP) requirements when interacting with other ULP processes. A unit may be created from a single disk drive or tape drive. A unit may also be created from a more complex container such as a RAIDset. The controller supports a maximum of eight units on each target. [. . . ]