User manual HP STORAGEWORKS XP COMMAND VIEW ADVANCED EDITION SOFTWARE

[. . . ] HP StorageWorks XP Command View Advanced Edition software Device Manager CLI user guide Version 6. 0 or later Reference number: T1780-96086 First edition: May 2008 Legal notices © Copyright 2008 Hewlett-Packard Development Company, L. P. Valid license from HP required for possession, use or copying. Consistent with FAR 12. 211 and 12. 212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U. S. Government under vendor's standard commercial license. [. . . ] If port and portname are omitted, information about all ports is displayed. If you specify this parameter, you must also specify the model and serialnum parameters. NOTE: Do not specify port and portname at the same time, as this might cause an error to occur. portsubinfo Optional Specific information about the ports The values you can specify are WWN, WWNGroup, LUNGroup, or HostStorageDomain. If you specify multiple values at the same time, separate the values by commas. Information obtained from a WWN group Specify WWNGroup in the parameter portsubinfo when using this parameter. Information obtained from a LUN group Specify LUNGroup in the parameter portsubinfo when using this parameter. Information obtained from paths of a LUN group Specify Path in the parameter lungroupsubinfo when using this parameter. The value you can specify is WWN or WWNGroup. Type of port about which you want to obtain information The values you can specify are LCP, Fibre, SCSI, NAS, and ISCSI. If you specify multiple values at the same time, separate the values by semicolons (;). wwngroupsubinfo# Optional lungroupsubinfo# Optional pathsubinfo# Optional portfilter Optional # This can only be specified for XP512/XP48. Command execution example: In this example, the CLI command obtains information about a port (port number: 0) in a subsystem (serial number: 10001, model: XP512) including WWNs, WWN groups, LUN groups, and the host storage domain. hdvmcli GetStorageArray -o "D:\logs\XP512 GetStorageArray_Port. log" subtarget=Port model=XP512 serialnum=10001 port=0 portsubinfo=WWN, WWNGroup, LUNGroup, HostStorageDomain wwngroupsubinfo=WWN Command execution result: RESPONSE: An instance of StorageArray . (Attributes of StorageArray are omitted here) . List of 1 Port elements: An instance of Port objectID=***** portID=0 portType=Fibre fibreAddress=EF topology=Fabric(off), FC-AL displayName=CL1-A lunSecurityEnabled=true controllerID=1 139 Command line interface commands worldWidePortName=50. 06. 0E. 80. 03. 3A. 99. 00 channelSpeed=1 portRole=Target slprNumber=-1 List of 2 WWN elements: An instance of WWN WWN=00. 00. 00. 00. 00. 00. 00. 01 nickname=Jane An instance of WWN WWN=00. 00. 00. 00. 00. 00. 00. 50 nickname=Jone List of 2 HostStorageDomain elements: An instance of HostStorageDomain objectID=***** portID=0 portName=CL1-A domainID=0 hostMode=Standard displayName=CL1-A-0 domainType=0 nickname=1A-G00 An instance of HostStorageDomain objectID=***** portID=0 portName=CL1-A domainID=1 hostMode=Standard displayName=CL1-A-1 domainType=0 nickname=HCMD0000 List of 1 WWNGroup elements: An instance of WWNGroup objectID=***** name=wwn group nickname=nickname List of 1 LUNGroup elements An instance of LUNGroup objectID=***** name=hp nickname=hp *****: The values are encoded by the CLI. 4-4-20-18 GetStorageArray (subtarget=PortController) GetStorageArray (subtarget=PortController) obtains the information about a port controller in one or all storage subsystems (see parameters in Table 4-51). A user to whom a user-defined resource group is assigned can obtain information about one or all port controllers in one or all storage subsystems that the user is permitted to access. Table 4-51 GetStorageArray (subtarget=PortController) command parameters Parameter Name model Status Optional Description Model of the storage subsystem If you omit this parameter, all the storage subsystems become the target. 140 Command line interface commands Table 4-51 GetStorageArray (subtarget=PortController) command parameters Parameter Name serialnum Status Optional Required Optional Description Serial number of the storage subsystem If you omit this parameter, all the storage subsystems become the target. Controller ID of the port controller in the storage subsystem Specify this parameter when you want to obtain information about a specific port controller. If you specify this parameter, you must also specify the model and serialnum parameters. If controllernum and controllername are omitted, all port controller information is obtained for the specified storage subsystem. NOTE: Do not specify controllernum and controllername at the same time, as this might cause an error to occur. subtarget controllernum controllername Optional Controller name for port controller of storage subsystem Specify this parameter when you want to obtain information about a specific port controller. If you specify this parameter, you must also specify the model and serialnum parameters. If controllernum and controllername are omitted, all port controller information is obtained for the specified storage subsystem. NOTE: Do not specify controllernum and controllername at the same time, as this might cause an error to occur. controllersubin fo Optional Specific information about the port controller you intend to obtain Available values are IPAddress and PairedPortController. [. . . ] The error message says: [KAIC07774-E] Failed to create a pair. This HORCM instance could not be started. The host used for creating the copy pair recognizes CL1-A or LUN0. Make sure that the DeviceManagerCLI. jar file has not been moved or renamed, and that you are executing from the directory where the hdvmcli. bat and DeviceManagerCLI. jar files reside. Assign another port to the LU or assign a LUN other than LUN0, and re-create the copy pair. Assign another port to the LU or assign a LUN other than LUN0, and re-create the copy pair. 314 Troubleshooting Table 6-1 General troubleshooting information Problem The following error message is displayed and the operation of Device Manager CLI is stopped: An unspecified error was encountered in CLI. Cause Recommended Action Collect the following information, and then contact your HP technical support representative. · CLI log file · CLI property file · Contents entered on the command line · An executed batch file if a batch was executed. · Device Manager server log. Text is omitted from the displayed error message. [. . . ]