User manual HP VECTRA VA 6/XXX

[. . . ] User's Guide HP Vectra VA 6/xxx Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information that is protected by copyright. [. . . ] a Ensure the PC's port has been correctly configured using Setup. b Make sure the printer is correctly set up in your operating system's configuration. c Ensure the application program's "print" menu has been correctly set up. (Refer to the manual supplied with the application software. ) Check that the PC's port is working properly by running another peripheral connected to the port. If you receive an error message, refer to the printer's manual for help. English 41 3 Troubleshooting Your PC If Your PC Has a Hardware Problem If the Flexible Disk Drive Does Not Work · · · · · · · Ensure you are using a formatted diskette and it is inserted correctly. Check you are using a diskette that is the right density. Check that your flexible disk drive is correctly configured in the Setup Configuration menu. Check the option on the Setup Configuration menu which enables or disables the on-board flexible disk controller. Clean the flexible disk drive using a diskette cleaning kit. Check that the flexible disk drive has been enabled in Setup. · Flexible disk drive (refer to the Hardware Protection Submenu of the Security Menu in the Setup Program) · Boot on flexible disk drive (refer to the Start-up Center Submenu of the Security Menu in the Setup Program) · Write on flexible disk drives (refer to the Start-up Center Submenu of the Security Menu in the Setup Program). Check that the disk power and data cables are correctly connected. If the Hard Disk Does Not Work Check that the disk power and data cables are correctly connected (refer to "Connecting IDE Devices", on page 18). · Check that the hard disk drive has been "enabled" (refer to the Hardware Protection Submenu of the Security Menu in the Setup Program). There is also an option in the Setup program that lets you disable or enable boot on hard disk drive (refer to the Start-up Center Submenu of the Security Menu in the Setup Program). · Check that the hard disk drive has been detected (refer to the IDE Devices Submenu of the Configuration Menu in the Setup Program). · Check that the on-board Bus IDE is enabled if you are using the integrated IDE controller (refer to the IDE Devices Submenu of the Configuration Menu in the Setup Program). · 42 English 3 Troubleshooting Your PC If Your PC Has a Hardware Problem If the Hard Disk Activity Light Does Not Work If the hard disk activity light does not flicker when the PC is accessing the hard disk drive: Check that the control panel connector is firmly attached to the system board. · Check that the disk power and data cables are correctly connected. · NOTE If you are using a hard disk drive with a controller board (a SCSI hard disk, for example), the activity light does not flicker when the PC is accessing the hard disk drive If the CD-ROM Drive Has a Problem WARNING Be sure to disconnect the power cord and any telecommunication cables from your computer before you remove the cover to check the cable connections or jumper settings. To avoid electric shock and harm to your eyes by laser light, do not open the CD-ROM drive enclosure. The CD-ROM drive should be serviced by qualified service personnel only. Do not attempt to make any adjustment of the unit. Refer to the label on the CD-ROM for power requirements and wavelength. This PC is a class 1 laser product. No Sound from the CD-ROM Drive If you are having problems with sound when playing a CD: · · · · Check that the volume control (if present) on the CD-ROM drive front panel is not set to the minimum. [. . . ] Export Administration regulations or other applicable regulation. Use, duplication, or disclosure by the U. S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause in DFARS 252. 227-7013. Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U. S. A. [. . . ]