User manual HP VECTRA XU 6/XXX

[. . . ] User's Guide HP Vectra XU 6/xxx Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. [. . . ] If this fails to correct the problem, the system board may need to be replaced. Contact your service representative. 8060 What you should do: 1 2 Check that the hard disk drive has not been disabled with the Setup program. Check that the disk power and data cables are correctly connected (refer to chapter 3). 910B Explanation: 1 2 You connected the flexible disk drive connector B to the disk drive, and there is no connection to a drive A. Change the flexible disk drive connector to A (refer to chapter 3). English 77 4 Troubleshooting Your PC and Using the Setup Program If Your PC Does Not Start BIOS Error Messages that May Prevent Your PC From Starting: Insert system diskette in drive. Explanation: · · · there is no operating system installed on your hard disk there is no operating system on the diskette in drive A the hard disk drive is disabled, or not present. What you should do: Install an operating system on the hard disk or insert a diskette with an operating system, and press any alphanumeric key to continue. Boot program in first sector of diskette is invalid, cannot start from this diskette. Missing operating system Explanation: There is a problem with the disk drive, or the disk drive is not properly formatted. What you should do: Insert a diskette with the proper operating system, and press any alphanumeric key to continue. Explanation: You tried to start the PC but the PC could not find the operating system. What you should do: Run Setup and make sure the hard disk has been correctly configured. 78 English 4 Troubleshooting Your PC and Using the Setup Program If Your PC Does Not Start System boot process failed. Press any key to try again. Explanation: You tried to start the PC but the PC could not find the operating system. What you should do: · · · · check the diskette contains the operating system check the hard disk contains the operating system ensure "start from the flexible disk" or "start from the hard disk" is enabled in Setup for a network, ensure "remote start" is enabled in Setup. Operating System Messages that May Prevent Your PC From Starting: Non-system disk or disk error What you should do: Remove the diskette, or replace it with the proper operating system diskette, and press any alphanumeric key to continue. Not ready error reading (or writing) drive x Explanation: The device specified in the error message is not ready to accept or transmit data. This could occur if: · · · The diskette has not been inserted correctly. If this is the problem, reinsert the diskette and type ``R'' (for Retry). The printer is not working--ensure it is on and ready to print. The device has been disabled using Setup. English 79 4 Troubleshooting Your PC and Using the Setup Program If Your PC Has a Hardware Problem If Your PC Has a Hardware Problem This section describes what to do if you have problems with your display, disk drives, printer, accessory boards, keyboard, or mouse. If Your Display Does Not Work If nothing is displayed on the screen, but the PC starts and the keyboard, disk drives, and other peripheral devices seem to operate properly: 1 Check that the brightness and contrast controls are properly set. 2 Make sure that the display is plugged in and switched ON. 3 Ensure that the display video cable is correctly connected to the display and to the PC. 4 Switch off the display, and unplug it from the power outlet. Examine the video cable pins to see if they are bent. If the display image is not aligned with the screen (usually when you change resolutions), use the display's controls to center the image. Refer to the display manual for instructions. [. . . ] Export Administration regulations or other applicable regulation. Use, duplication, or disclosure by the U. S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause in DFARS 252. 227-7013. Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U. S. A. [. . . ]