User manual HP VISUALIZATION CENTER SV6-ENTRY

[. . . ] installation and user's guide hp visualization center sv6 Manufacturing Part Number: A6062-90005 Edition: E0302 Printed in U. S. A legal notices The information in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this manual, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be held liable for errors contained herein or direct, indirect, special, incidental or consequential damages in connection with the furnishing, performance, or use of this material. Use, duplication or disclosure by the U. S. Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS 252. 227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the Commercial Computer Software Restricted Rights clause at FAR 52. 227-19 for other agencies. [. . . ] Select the Backdrop option from the Style Manager 3. It may take some time to open the menu as CDE first scans the large files and adds them to the file browser. Select a backdrop to display as depicted in the following page. Select the Apply button to make it the current backdrop. 60 Chapter 2 installation and user information advanced setup for multiple display channels Figure 2-20 3840 x 1024 3x(1280 x 1024) cst3840. pm grdc3840. pm fish3840. pm Figure 2-21 3072 x 768 3x(1024 x 768) cst3072. pm grdc3072. pm fish3072. pm Chapter 2 61 installation and user information usage usage This section covers some general tasks the hp visualization center sv6 user may do. If you are looking for descriptions of hp visualization center sv6 tools, skip to the How To Use hp visualization center sv6 Tools section. · X Server To start the X server on the master system, run X:0 or go to init 3 to start up the X server and CDE. The master's X server will automatically start and control all slave X servers on the other systems. To kill the X server, press <Ctrl>+<Shift>+<Break>, then wait for the X servers to stop. Press <Ctrl>+<Shift>+<Break> again. Press enter a couple of times to get the prompt back. · X0screens Description The /etc/X11/X0screens file details the X server configuration information for the HP X server. The X0screens file is used to configure many aspects of hp visualization center sv6 including which systems are to be involved in the hp visualization center sv6 configuration, video timing data, and options to obtain diagnostic information. The X0screens file on the hp visualization center sv6 master system is used to configure the X servers on each of the hp visualization center sv6 slave systems. This single-file configuration maintains consistency between all nodes. NOTE This file must be edited as root and must be located in /etc/X11/X0screens · Loading X0screens templates A template /etc/X11/X0screens file is on the master system. There are several additional X0screens template files available. Copy or link the desired (and compatible) template to X0screens. For 62 Chapter 2 installation and user information usage instance, if you have a three channel system, but you want to temporarily set the configuration to use only two of the channels, you could save the current X0screens file and move a two channel template into place: cp /etc/X11/X0screens /etc/X11/X0screens. orig cd /usr/lib/X11/Xserver/misc/slsd/templates cp X0screens. p16c2 /etc/X11/X0screens . or ln -s /etc/X11/X0screens. 16c2 /etc/X11/X0screens NOTE Early versions of SLS/d required the /etc/X11/X0devices and /etc/X11/X0screens files on the slave systems to be edited. This is no longer necessary, since the master system uses the information in its X0screens file to do automatic configuration on the slaves via the X server. changing resolution Use one of the methods below to specify the resolution in the /etc/X11/X0screens file. Each method automatically sets all graphics cards in the hp visualization center sv6 configuration to the specified resolution. If no video timing information is specified, the default settings will be used. Do not use the setmon program to change resolutions on your systems. [. . . ] passive stereo - Stereo capability where no emitter is need. Uses a combination of polarized glasses and special output display devices (i. e. specially aligned projectors or Glossary passive stereo work bench displays). The glasses filter out the correct image for the right and left eye. [. . . ]