User manual HP VISUALIZE C110 WORKSTATION

[. . . ] Model C100/110 Owner's Guide HEWLETT® PACKARD HP Part No. A4200-90014 Edition E0995 Printed in U. S. A. © Hewlett-Packard Co. 1995 Printing History First Printing: September 1995 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice. HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. [. . . ] The host SCSI controllers use SCSI ID 7. NOTICE: 119 Changing Your Workstation's Hardware Configuration Installing Storage Devices Preparing to Install Your Storage Device This section describes information that you need to consider and procedures that you need to perform before installing any storage device. Configuring your Storage Device Table 13 lists the recommended SCSI IDs for internal storage devices. If an existing device already uses one of the suggested IDs, select an alternate ID. Table 13 Default SCSI IDs Fast/Wide Differential SCSI Devices 1st Hard Disk Drive 2nd Hard Disk Drive 3rd Hard Disk Drive Single-Ended SCSI-2 Devices CD-ROM Drive DDS-Format Tape Drive SCSI ID 6 5 4 SCSI ID 2 3 NOTE: The floppy drive is not a SCSI device. Set the jumpers and SCSI IDs according to the installation instructions that came with your device. Determining Your Storage Devices Position Each storage device is restricted as to where in the storage tray it may be installed. Before installing a storage device, use Figure 21 and Table 14 to determine which disk tray position is correct for your device. Figure 21 shows the storage device positions in the disk tray. Table 14 lists what devices are supported in the different disk tray positions. The numbers in the table's left column refer to the position numbers in Figure 21. 120 Changing Your Workstation's Hardware Configuration Installing Storage Devices Figure 21 Table 14 Disk Tray Positions Storage Configurations Disk Tray Position 1 Supported Devices Conditions Floppy Drive 1-inch Low Profile Disk Drive 2 CD-ROM DDS-Tape 3 1-inch Low Profile Disk Drive 1. 6-inch Full Height Disk Drive If a CD-ROM drive is installed, install a 1. 6-inch full height disk drive in this position. 4 1-inch Low Profile Disk Drive 1. 6-inch Full Height Disk Drive This is the preferred position for a 1. 6-inch full height disk drive. If a CD-ROM drive is installed, a 1. 6inch full height disk drive cannot be installed in this position. All hard disk drives are fast, wide SCSI devices. The CD-ROM drive and the DDS tape drive are single-ended SCSI devices. The floppy drive is not a SCSI device. 121 Changing Your Workstation's Hardware Configuration Installing Storage Devices Mounting the Storage Device Slides From the accessory hardware kit which came with your workstation, locate two plastic storage device slides. Using the screws that came with the storage device, mount the slides on the new storage device so that the locking tabs are at the connector end of the drive, as shown in Figure 22. Locking Tab Figure 22 CAUTION: Mounting the Storage Device Slides When mounting the storage device slides, only use the screws that shipped with the storage device. Use of other screws can cause physical damage to the device. 122 Changing Your Workstation's Hardware Configuration Installing Storage Devices Storage Device Cable Routing When you install your storage device, be aware of the suggested cable routing paths as indicated in the cable routing label that is affixed to the top of the storage tray. Disk Shield If you are installing a hard disk manufactured by Hewlett-Packard, you need to install a disk shield. 1 Check the manufacturer's labeling on the disk drive to determine if it is a disk manufactured by Hewlett-Packard. If the disk is not a Hewlett-Packard disk, skip the rest of this procedure. 2 3 From the accessory hardware kit which came with your workstation, locate the disk shield and four screws. See Figure 23. Use the four screws to mount the disk shield on the drive, as shown in Figure 23. Figure 23 Mounting the Disk Shield 123 Changing Your Workstation's Hardware Configuration Installing Storage Devices Removing the Disk Tray Perform the following procedure to remove the Storage Tray from the system unit: 1 2 3 Remove the storage tray retaining screw, as shown in Figure 24. If installed, remove any locking device from the storage tray security loop on the rear of the system unit. Place your fingertips in the groove on the bottom of the storage tray bezel. See Figure 24. Retaining Screw Figure 24 Removing the Storage Tray 4 CAUTION: Slide the storage tray completely out of the system unit. Be sure to support the storage tray from underneath while sliding it out of the system unit. Proceed to one of the following sections in this chapter to install your storage device in the disk tray: · · · Installing a CD-ROM or a DDS-Format Tape Drive Installing a Floppy Drive Installing a Hard Disk Drive in Position 3 or Position 4 124 Changing Your Workstation's Hardware Configuration Installing Storage Devices Installing a CD-ROM or a DDS-Format Tape Drive Perform the following procedure to install a CD-ROM or DDS tape drive in the disk tray: 1 Remove the disk filler panel from the top location of the bezel by using a coin or other flat, blunt, object to pry it from the front. , as shown in Figure 25. Figure 25 Removing a Disk Filler Panel 125 Changing Your Workstation's Hardware Configuration Installing Storage Devices 2 From the rear of the storage tray, line up the disk slides on the CD-ROM or DDS tape drive with the position 1slots in the storage tray chassis, and slide it into place, as shown in Figure 26. CD-ROM or DDS Tape Drive Cable Routing Label Figure 26 Installing a CD-ROM or DDS Tape 3 4 5 Push the storage device in until the locking tabs snap into place. Connect the single-ended SCSI-2 data cable and the power cable to the drive. Refer to the cable routing label on the storage tray. Proceed to the section entitled Replacing the Storage Tray. 126 Changing Your Workstation's Hardware Configuration Installing Storage Devices Installing a Floppy Drive Perform the following procedure to install a floppy drive in the disk tray: 1 Remove the disk filler panel from the bottom location of the bezel by using a coin or other flat, blunt, object to pry it from the front, as shown in Figure 27. Figure 27 Removing a Disk Filler Panel 2 Reach into the storage bay and locate the power and data cables for the floppy drive. Refer to the cable routing label on the storage tray. 3 Connect the cables to the drive. 127 Changing Your Workstation's Hardware Configuration Installing Storage Devices 4 From the front of the storage tray, line up the disk slides on the floppy drive with the position 2 slots in the storage tray chassis and slide it into place, as shown in Figure 28. Cable Routing Label Figure 28 Installing a Floppy Drive 5 6 Push the floppy drive in until the locking tabs snap into place. Proceed to the section entitled Replacing the Storage Tray. 128 Changing Your Workstation's Hardware Configuration Installing Storage Devices Installing a Hard Disk Drive in Position 1 Perform the following procedure to install a hard disk drive: 1 Remove the disk filler panel from the bottom location of the bezel by using a coin or other flat, blunt, object to pry it from the front, as shown in Figure 29. Figure 29 Removing a Disk Filler Panel 2 Reach into the storage bay and locate the power and data cables for the disk drive. [. . . ] transceiver A device that transmits and receives signals. user account The system administrator defines a user account for every person authorized to use the system. Each user account contains the name the computer uses to identify the person (user ID), and the person's password. User accounts also contain project and organization names, to help the system determine who can use the system and what resources each person or organization can use. [. . . ]