User manual HP VISUALIZE C360 WORKSTATION

[. . . ] Model C160 / C180 / C200 / C240 / C360 Owner's Guide HP Part No. A4200-90050 Edition E1298 Printed in U. S. A. Copyright © Hewlett-Packard Co. 1998 Printing History First Printing: December 1998 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice. HEWLETT-PACKARD WARRANTY STATEMENT HP PRODUCT DURATION OF WARRANTY one year C160/C180/C200/C240/C360 1. [. . . ] NOTICE: Memory slots must be filled in order from 0A and 0B through 5A and 5B. 127 Changing Your Workstation's Hardware Configuration Installing Additional Memory 3 Close the ejector tabs on each side of the memory connector to lessen the force needed to seat the memory module. See Figure 41. White Ejector Tab Figure 41 Installing Memory Modules 4 5 Place the memory module in the connector, lining it up with the guides. Make sure to put the notched end toward the white ejector tab, as shown in Figure 41. Press firmly and evenly on the memory module to ensure that it seats properly. 128 Changing Your Workstation's Hardware Configuration Installing Additional Memory 6 Replace the main tray assembly as described in "Replacing the Main Tray Assembly, " earlier in this appendix. To verify that this installation was successful, follow the steps in Appendix D, "The Boot Console Interface, " on displaying memory information. If you have only replaced a faulty memory module, you must issue the pdt clear command in the service menu of the Boot Console Interface. Answer yes (y) to the prompt "Continue?(Y/N) >. " 129 Changing Your Workstation's Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) Before installing the EGRAM module, perform the procedure in Removing the Main Tray Assembly on page 122. Perform the following steps to add the EGRAM module to your workstation: 1 Press the release clip and rotate the EISA fan, as shown in Figure 42. Figure 42 Rotating the EISA Fan 130 Changing Your Workstation's Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 2 3 Slide the EISA slider to the side to remove it, as shown in Figure 43. Remove the screw from the EISA retainer and remove it, as shown in Figure 43. EISA Slider EISA Retainer Figure 43 Removing the EISA Slider and Retainer 4 Grasp the option board by the edge with both hands and pull it straight out. Remove all option boards, making note of which option slot each one was installed in. NOTICE All boards must be replaced in their original slots or your system may not run properly. 131 Changing Your Workstation's Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 5 6 Install the standoffs into the EGRAM module, as shown in Figure 44. Push the standoffs into the holes on the module until the clips fully emgage with the board. Align the connector on the EGRAM module with the connector on the I/O board, while aligning the standoffs with the holes in the I/O board. See Figure 44. Figure 44 Installing the EGRAM Module 7 Connect the EGRAM module to the I/O board. Push down firmly on the connector area to make sure it is fully seated. Push firmly near the standoffs to make sure that they are fully engaged with the I/O board. 132 Changing Your Workstation's Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 8 Make sure that the EISA fan is fully rotated, as shown in Figure 45. Figure 45 Rotating the EISA Fan 9 Slide the option boards into the slots that they came out of, as shown in Figure 46. Make sure that the hole in each board's handle aligns with the pin on the back panel. Figure 46 Installing an Option Board 133 Changing Your Workstation's Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 10 Press in firmly on both ends of the option board at the same time to make sure that it is firmly seated in the backplane connector. 11 Replace the EISA retainer and its screw, as shown in Figure 47. 12 Replace the EISA slider, as shown in Figure 47. Figure 47 Installing the EISA Retainer and EISA Slider 134 Changing Your Workstation's Hardware Configuration Installing the EGRAM (Enhanced Graphics RAM) Module (C160/C180) 13 Rotate the fan back into place, as shown in Figure 48. Push it into the rear panel firmly until the clip snaps into place. Figure 48 Securing the Fan 14 Replace the main tray assembly as described in Replacing the Main Tray Assembly on page 124. 135 Changing Your Workstation's Hardware Configuration Installing an EISA, PCI, or GSC Option Board Installing an EISA, PCI, or GSC Option Board Your workstation has 4 option slots, as shown in Figure 49. On C160/C180 workstations, slots 1 and 2 each support either GSC or EISA boards. Slot 3 supports a GSC, EISA, or PCI board. On C200/C240/C360 workstations, slots 1, 2, 3 and 4 each support either GSC or PCI boards. [. . . ] See also fast wide differential SCSI, Small Computer System Interface. user account The system administrator defines a user account for every person authorized to use the system. Each user account contains the name the computer uses to identify the person (user ID), and the person's password. User accounts also contain project and organization names, to help the system determine who can use the system and what resources each person or organization can use. [. . . ]