User manual HP W17E 17-INCH WIDESCREEN LCD MONITOR

[. . . ] Back to Contents Page w17e/W17q LCD Monitor User's Guide · · · · · · · · · Preface Safety and Maintenance Guidelines Setup Using the Monitor Installing Drivers and Using the Auto-Adjustment Feature Technical Support FAQs Specifications LCD Monitor Quality and Pixel Policy Agency Regulatory Notices The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. HP assumes no responsibility for the use or reliability of its software on equipment that is not furnished by HP. [. . . ] Line up the holes of the arm with the mounting holes in the back of the monitor. 3 Insert four screws into the mounting holes and tighten. Refer to the user's manual that came with the wall mounting arm (purchased separately) for instructions on attaching it to the wall. Back to Contents Page Using the Monitor Operating Instructions · External Controls · LED Indicators · Settings · Setting the Optimal Resolution · Adjusting the Volume · Locking the OSD · Adjusting OSD Settings · OSD Menu Operating Instructions Control buttons are located on the front of the panel, as shown in the illustration following. Use the Menu button to adjust the display settings to your personal preferences: · · · · · Set up the monitor, attach the cables, and adjust the tilt as described in the Setup section above. Press the power button to turn the monitor on and off. The power indicator lights up when the monitor is on. The monitor must be turned on for the other control buttons to work. Set the resolution (Setting the Optimal Resolution) and adjust the volume (Adjusting the Volume). Adjust the onscreen display (OSD) settings (Adjusting OSD Settings). External Controls A B C D E F Auto-configuration / Exit Volume decrease / Left navigation Volume increase / Right navigation Menu / Enter Power LED indicator LED Indicators Status Full Power Mode Power Save Mode LED Color Green Amber See Technical Support FAQs for more information. Back to Contents Page Settings Setting the Optimal Resolution · Adjusting the Volume · Locking the OSD · Adjusting OSD Settings · OSD Menu Setting the Optimal Resolution The recommended resolution for this monitor is 1440 by 900. To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the following: 1 Click the Windows Start Button , and then click Control Panel. 2 Under Appearance and Personalization, click Adjust Screen Resolution. 3 Set the resolution slide bar to 1440 by 900. NOTE: If 1440 by 900 is not shown, download the monitor driver from the Web. See Using the Monitor for instructions. Adjusting the Volume Press the front monitor panel volume increase and decrease buttons to adjust volume to the desired level. Volume cannot be adjusted through the OSD menu. Locking the OSD To lock the OSD (onscreen display), press and hold the Menu button while the monitor is off, then press the power button to turn the monitor on. To unlock the OSD, repeat the locking procedure. The software download pages for your monitor will be displayed. Download and install the driver and software files using the instructions in the download pages. Using the Auto-Adjustment Function Press the Auto button to optimize the screen performance for VGA (analog). You can also access the Auto-adjustment feature through the OSD menu. Auto-adjustment can correct the following image quality conditions: · · · · · Fuzzy or unclear focus Ghosting, streaking, or shadowing effects Faint vertical bars Thin, horizontal scrolling lines An off-center picture Back to Contents Page Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Technical Support FAQs (Frequently Asked Questions) Problem & Question Power LED is not on No Plug & Play Possible Solutions · Make sure the Power button is on and the power cord is properly connected to a grounded power outlet and to the monitor. · In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer and video card. · Check the monitor's video cable and make sure none of the pins are bent. · Make sure the HP monitor drivers are installed (HP monitor drivers are available at: http://www. hp. com/support). Picture is fuzzy and has ghosting shadowing problem · Adjust the contrast and brightness controls. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. [. . . ]