Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HUBBELL LIGHTING 5010. We hope that this HUBBELL LIGHTING 5010 user guide will be useful to you.
Lastmanuals help download the user guide HUBBELL LIGHTING 5010.
Detailed instructions for use are in the User's Guide.
[. . . ] Reflector can be relamped without removing wire guard. FIGURE 2 FIGURA 2
INSTALLATION OF GUARD TO A REFLECTOR WITH A LENS ASSEMBLY IN PLACE - FIGURE 3 AND 4 1. Orient the clamps on the guard approximately 90° from the hinge bracket (8) location on the reflector flange. [. . . ] Spread and raise the guard over the reflector flange (5) and over the lens ring spring latches (7) holding the lens assembly (10) in place. Place the top ring (9) of the wire guard inside the open loop of the lens ring spring latches as shown. Tighten screws (1) to clamp guard on reflector. The guard must be removed for relamping.
FIGURE 3 FIGURA 3
FIGURE 4 FIGURA 4
268-1153-9901
INSTRUCTIONS D'INSTALLATION DES APPAREILS DE LA PROTECTEURS EN FIL MÉTALLIQUE WG-19 et 5010
MISE EN GARDE: Manipuler et installer le protecteur en fil métallique de manère à ce qu'il ne puisse tomber. INSTRUCTIONS GÉNÉRALES - FIGURE 1 1. Insérer vis (1) dans les trous des plaques pilèes vers l'extérieur (3) sur le protecteur (4) et installer l'écrou (2), comme l'indique le schéma. INSTALLATION DU PROTECTEUR SUR UN RÉFLECTEUR - FIGURE 2 1. On doit enlever le protecteur avant de remplacer la lampe.
INSTRUCCIONES DE INSTALACION DE LOS APARATOS DE LA PROTECTORES DE HILO DE GUARDA WG-19 y 5010
PRECAUCIONES: Manipule e instale el protector de hilo de guarda de forma que no pueda caerse. Instale el tornillo (1) y la tuerca (2) en los agujeros de las placas orientadas hacia el exterior (3) sobre el protector (4) tal y como se indica en el esquema. INSTALACION DEL PROTECTOR SOBRE UN REFLECTOR - FIGURA 2 1. Estire el protector y colóquelo por encima de la pestaña del reflector (5). Asegúrese de que los extremos doblados hacia el interior (6) de la parte superior del protector de hilo de guarda pasan por encima de la pestaña del reflector, para evitar que el protector se separe de la pestaña. Atornille los tornillos (1) para fijar el protector al reflector. No los apriete demasiado para que la apertura del reflector no se deforme. [. . . ] No los apriete demasiado para que la apertura del reflector no se deforme. La lámpara del reflector podrá ser sustituida sin necesidad de quitar el protector de hilo de guarda. INSTALACION DEL PROTECTOR SOBRE UN REFLECTOR DOTADO DE UNA LENTE - FIGURAS 3 Y 4 1. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HUBBELL LIGHTING 5010
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HUBBELL LIGHTING 5010 will begin.
