User manual HUBBELL LIGHTING CH-TLRX

[. . . ] Çamaþýr makinesinin ambalajdan çýkartýlmasý 2. Çamaþýr makinesinin taþýma esnasýnda hasar görmemiþ olduðunu kontrol ediniz. Hasar görmüþ ise monte etmeyiniz ve yetkili satýcýyla temas kurunuz. TTaþýma sýrasýnda arka tarafta bulunan 3 adet koruyucu vidayý ve ara parçasýyla birlikte buradaki lastiði de çýkartýnýz (resime bkz. ). 4. [. . . ] • Su musluðu açýk deðil. • Baþlangýç zamanýný erteleme programlanmýþ (zaman ayarý, bkz. • • • • • • Su giriþ hortumu musluða takýlý deðil. Su musluðu açýk deðil. BAÞLAT/TEKRAR BAÞLAT düðmesine basýlmadý. Montaj Taným Çamaþýr makinesi su almýyor. (Iþýklý göstergede H2O ibaresi görüntüleniyor). Programlar Çamaþýr makinesi devamlý su alýp veriyor. • Boþaltma hortumu zeminden 65 ile 100 cm arasýnda yerleþtirilmemiþ (bkz. • Boþaltma hortumu suya girmiþ (bkz. • Duvardaki tahliyenin hava boþluðu yok. Bu kontrollerdan sonra olumlu sonuç alýnamazsa, musluðu kapatýp, çamaþýr makinesini durdurarak Ariston Yetkili Servisine haber veriniz. Oturduðunuz kat binanýn üst katlarýndaysa, sifon etkisi sebebiyle çamaþýr makinesi devamlý su alýp, veriyor olabilir. Bu sorunun çözümü için piyasada sifon önleyici valfler satýlmaktadýr. Deterjanlar Önlemler Çamaþýr makinesi su boþaltmýyor veya sýkma yapmýyor. • Program su boþaltmayý öngörmüyor: bazý programlarda su boþaltma iþlemini elle müdahale ederek baþlatmak gerekir (bkz. The water supply marked C must be connected to the cold water tap; the pipe marked H must be connected to the hot water tap. Both pipes may be connected to the cold water tap using the special Y connection with multiple attachments, supplied with the appliance (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. Warning: clean the filters regularly by rinsing it under running water. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure). Make sure there are no kinks or bends in the hose.  Packaging materials are not children's toys. Levelling 1. Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets or other. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured according to the worktop, must not exceed 2°.  The water pressure at the tap must be within the values indicated in the Technical details table (on the next page).  If the water inlet hose is not long enough, contact a specialist store or an authorised serviceman. 14 Connecting the drain hose  Do not use extensions or multiple sockets. Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; GB Installation  The power supply cable must never be bent or dangerously compressed.  The power supply cable must only be replaced by an authorised serviceman. Warning!The company denies all liability if and when these norms are not respected. 65 - 100 cm Description The first wash cycle alternatively, place it over the edge of a basin, sink or tub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater. [. . . ] Wash it under running water; this operation should be repeated frequently. 2 2. unscrew the lid rotating it anticlockwise (see figure): a little water may trickle out. This is perfectly normal; Caring for your appliance door and drum • Always leave the appliance door ajar to prevent unpleasant odours from forming. reposition the panel, making sure the hooks are securely in place before you push it onto the appliance. Checking the water inlet hose Check the water inlet hose at least once a year. [. . . ]