User manual HUBBELL LIGHTING EVRS-ADP-X

[. . . ] · The use of optical instruments with this product will increase eye hazard. Notes on the power supply cord (yellow) · When connecting this unit in combination with other stereo components, the connected car circuit's rating must be higher than the sum of each component's fuse. · When no car circuits are rated high enough, connect the unit directly to the battery. 4 5 6 ×6 ×6 4 For NISSAN cars only 7 amplifier This connection is only for amplifiers. [. . . ] To the interface cable of a car telephone To a car's illumination feed Be sure to connect the black ground lead to it first. To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes · If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black ground lead to it first. · When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes on the control and power supply leads. " To the +12 V power terminal which is energised at all times Be sure to connect the black ground lead to it first. Equipment used in illustrations (not supplied) Front speaker Power amplifier Parts Iist (1) The numbers in the list are keyed to those in the instructions. Notes on the control and power supply leads · The power antenna control lead (blue) supplies +12 V DC when you turn on the tuner. · When your car has built-in FM/AM antenna in the rear/side glass, connect the power antenna control lead (blue) or the accessory power input lead (red) to the power terminal of the existing antenna booster. · A power antenna without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned off. Notes on speaker connection · Before connecting the speakers, turn the unit off. ·Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts. ·Use only the supplied mounting hardware for a safe and secure installation. When mounting this unit to the preinstalled brackets of your car, use the supplied screws 1 or 2 in the appropriate screw holes, according to your vehicle: T for TOYOTA, M for MITSUBISHI, and N for NISSAN. N M T T M N T 1 · · 2 N M M T N T T · T T N N T M N N N T M N Mounting angle adjustment Adjust the mounting angle to less than 20°. Frequency select switch The AM (FM) tuning interval is factory-set to the 9 k (50 k) position. If the frequency allocation system of your country is based on 10 kHz (200 kHz) interval, set the switch on the left side of the unit to the 10 k (200 k) position before making connections. After the frequency select switch is set, you must press the reset button to reset the unit. N M T T M N T Notes · Use the screws 1 or 2 depending on the make of car. When this unit is attached to a MITSUBISHI car, use the supplied screws 2. · To prevent malfunction, be sure to install using brackets and the supplied screws 1 or 2. · Do not apply excessive force to the buttons of the unit. · Do not push on the display window. [. . . ] · Do not push on the display window. · Before mounting, make sure there is nothing on the top of the unit. · · 1 · · · 2 1 2 2 N M T T M N T T T N N T M N Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) only momentarily, the clock display does not turn off and this causes battery wear. N N T M N (OFF) (OFF) CD To set the frequency select switch, use a pointed object, such as a ball-point pen, to gently slide the switch. DSO EQ7 Reset button When the installation and connections are completed, be sure to press the reset button with a ball-point pen, etc. SCRL OFF DSPL SA ATT MD 4 SEEK/AMS SEEK/AMS SOUND MENU MODE SOURCE Mounting the unit in a Japanese car (4) You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer. DSO SCRL OFF DSPL CD EQ7 SA ATT MD SEEK/AMS SEEK/AMS SOUND MENU MODE SOURCE Reset button Note When you connect the power supply cord to the unit or reset the unit, wait for about 10 seconds before you insert a disc. [. . . ]