User manual HUBBELL LIGHTING STEP

[. . . ] Çamaþýr makinesinin ambalajdan çýkartýlmasý 2. Çamaþýr makinesinin taþýma esnasýnda hasar görmemiþ olduðunu kontrol ediniz. Hasar görmüþ ise monte etmeyiniz ve yetkili satýcýyla temas kurunuz. Taþýma esnasýnda güvenliði saðlayan dört adet koruma vidasýný sökün ve üst kýsýmdaki plastik separatörü çýkartýnýz (resime bkz. ). 4. [. . . ] Su musluðu açýk deðil. Baþlangýç zamanýný erteleme programlanmýþ (zaman ayarý, bkz. Su giriþ hortumu musluða takýlý deðil. Su musluðu açýk deðil. BAÞLAT/TEKRAR BAÞLAT düðmesine basýlmadý. Taným Çamaþýr makinesi su almýyor. Programlar Çamaþýr makinesi devamlý su alýp veriyor. • Boþaltma hortumu zeminden 65 ile 100 cm arasýnda yerleþtirilmemiþ (bkz. • Boþaltma hortumu suya girmiþ (bkz. • Duvardaki tahliyenin hava boþluðu yok. Bu kontrollerdan sonra olumlu sonuç alýnamazsa, musluðu kapatýp, çamaþýr makinesini durdurarak Ariston Yetkili Servisine haber veriniz. Oturduðunuz kat binanýn üst katlarýndaysa, sifon etkisi sebebiyle çamaþýr makinesi devamlý su alýp, veriyor olabilir. Bu sorunun çözümü için piyasada sifon önleyici valfler satýlmaktadýr. • Program su boþaltmayý öngörmüyor: bazý programlarda su boþaltma iþlemini elle müdahale ederek baþlatmak gerekir (bkz. Remove the three protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure). Electric and water connections Connecting the water inlet hose 4. Seal the gaps using the plastic plugs provided. Use the plug provided to seal the three holes where the plug was housed, situated on the lower right-hand side on the rear of your appliance. Keep all the parts: you will need them again if the washing machine needs to be moved to another location. 1. Connect the supply pipe to the water mains using a gas 3/4 attachment, fitting the rubber gasket and the filter supplied with the appliance and ensuring that they are fimly tightened to the taps. The water supply marked C must be connected to the cold water tap; the pipe marked H must be connected to the hot water tap. Both pipes may be connected to the cold water tap using the special Y connection with multiple attachments, supplied with the appliance (see figure). Before making the connection, allow the water to run freely until it is perfectly clear. Warning: clean the filters regularly by rinsing it under running water. Connect the other end of the water inlet hose to the washing machine, screwing it onto the appliance's cold water inlet, situated on the top right-hand side on the rear of the appliance (see figure). Make sure there are no kinks or bends in the hose.  Packaging materials are not children's toys. Levelling Your machine may make a considerable amount of noise if the two front feet have not been adjusted correctly. [. . . ] • • • • • • • • • • • The appliance door is not shut properly. The START/RESET button has not been pressed. A delayed start has been set (using the Delay Timer, see page 19). The water inlet hose is not connected to the tap. [. . . ]