User manual HUGHES & KETTNER CLUB REVERB

[. . . ] BEDIENUNGSANLEITUNG MANUAL ENGLISH DEUTSCH illustrations CAUTION!230 V~ 100 V~ 117 V~ T 0, 5 A SB 1250 mA SB 1000 mA TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD DON´T EXPOSE THIS APPLIANCE TO MOISTURE OR RAIN. DO NOT OPEN CASE; NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. MADE IN ST. [. . . ] 6. 3 The footswitch does not switch channels: - The footswitch is not connected to the CLUB REVERB. - Check whether your footswitch is of the correct type. We recommend a Hughes & Kettner FS-1. 6. 4 When accessed, the LINE OUT/LINE IN jacks cause annoying hum. - An electrical or magnetic field is causing interference. Use higher-quality cables or re-arrange the cables you are using to reduce interference to a minimum. If this still doesn't improve the situation, use a DI box. - The grounding of the connected devices may be causing a ground loop. DO NOT SEVER THE GROUND OF THE CONNECTED DEVICES UNDER ANY CIRCUMSTANCES! 6. 0 TROUBLESHOOTING 6. 1 The CLUB REVERB will not switch on: - The amp is not getting any AC power. Check the mains cable to see if it is connected properly. Replace the fuse with another Try plugging all devices into the same socket via an AC power distributor/power strip. If this doesn't eliminate the noise, you must ensure the connection is galvanically separated by routing the signal through a DI box. 6. 5 You have connected an FX processor to the LINE OUT jack and the signal is totally distorted, even when you have dialed in a clean sound. - The LINE OUT signal is overloading the input of the FX processor. Reduce the processor`s input sensitivity ("INPUT" or "GAIN"). 6. 6 You have connected an FX processor to the LINE OUT jack of the CLUB REVERB and the signal's volume level is way too low. - The FX processor's output level is set incorrectly. Turn it up. Output Power: 65 watts rms into 8 ohms Freqency response: 20 Hz - 30 kHz (into 8 ohms) Speaker: CELESTION RockDriver Junior, 12", 8 ohms General features: Voltage: 230 V~ (European model) 117 V~ (North American model) 100 V~ (Japanese model) Max. power consumption: 175 VA Mains Fuse: slo-blo 500 mA (230 V model) slo-blo 1000 mA (117 V model) slo-blo 1250 mA (100 V model) 7. 0 TECHNICAL DATA Preamp Section Preamp section: CLEAN + LEAD solid state channels INPUT: LINE OUT: LINE IN: -10 dBV/ 1 M ohm 0 dBV/ 1k ohm 0 dBV/ 47 k ohms Dimensions: (W x H x D) 464 x 480 x 265 mms 18" x 18. 9" x 10. 4" Weight: approx. 33 lbs. /approx. 15 kgs. Power amp section:: 'CURRENT FEEDBACK' solid state power amp Wir freuen uns, daß Du Dich für einen HUGHES & KETTNER CLUB REVERB entschieden hast! Ein Team aus Gitarristen und Technikern hat die Verstärker der ATTAX Series mit dem Ziel entwickelt, anspruchsvolle Gitarrensounds mit einfachster Bedienung und praxisgerechter Ausstattung zu kombinieren. Der CLUB REVERB ist das ideale Arbeitsgerät für anspruchsvolle Gitarristen, die amtliche Grundsounds in einem kompakten Amp fordern. Seine leistungsstarke Current Feedback Endstufe sorgt nicht nur für 65 Watt Leistung, sondern auch für offenen "Röhrencharakter". [. . . ] Die Oberfläche des CLUB REVERB läßt sich am besten mit einem leicht angefeuchtetem Tuch säubern. durch eine neue Sicherung mit entsprechendem Wert. Wende dich bei erneutem Defekt an Deinen Hughes & Kettner Fachhändler. 6. 2 Der CLUB REVERB ist korrekt verkabelt, aber es ist nichts zu hören: - Einer oder mehrere der Gain- bzw. nicht in Ordnung, probiere es mit einem anderen. [. . . ]