User manual HUGHES & KETTNER ZENAMP

[. . . ] www. hughes-and-kettner. com BEDIENUNGSANLEITUNG zenAmp DYNAMIC SECTOR MODELING TM GUITAR AMP MANUAL 1. 0 ENGLISH ZENAMP-MANUAL zenAmp DYNAMIC SECTOR MODELING TM GUITAR AMP This operating manual is also available as a computer file. To download it, go to www. hughes-and-kettner. com, then to "Manuals". Hughes & Kettner, zenAmp, DSM, Dynamic Sector Modeling, Z-Board, FS-5, the Hughes & Kettner logo, the zenAmp logo, the DSM Logo, Montana, WARP 7, and ATS 112 are trademarks or registered trademarks of Hughes & Kettner. All other product names are the property of their respective owners. CONGRATULATIONS AND THANK YOU FOR CHOOSING THE ZENAMP! The findings of 20 years of research at Hughes & Kettner flowed into the zenAmp. [. . . ] This switches the zenAmp to Manual mode (see section 4. 2 above). Briefly press the MANUAL button again to switch to Preset mode, which lets you access the user presets. The optional Z-Board is of course a far more convenient option for switching modes and presets. Here's how this works: Press the STORE button. Select the desired memory slot by pressing one of the PRESET buttons 1 to 5. The preset is stored when you press STORE again. This overwrites the preset that was previously stored in the selected memory slot. Note: You can cancel the storage process at any time by pressing the MANUAL button. Note also: You can of course also navigate to the desired memory slot via the optional Z-Board. FX TYPE: This selector puts eight modulation effects, seven pre effects (meaning effects that plug into the front end of the amp) such as wah-wah, and a bypass at your fingertips. Simply turn the rotary selector to select effects. FX PARAMETER: Controls the parameters of the effect that you select using the FX TYPE knob. Since most of the effects offer at least two parameters, this knob actually gives you musically meaningful combinations of these parameters. Case in point: Say you select the chorus effect. When the FX PARAMETER knob is set to a low value, the chorus' rate is low, but its intensity or amount is high. As you turn the knob up, the rate increases while intensity decreases. REVERB VOL: It determines the amount of reverb that is added to the signal. TAP: This button lets you enter in delay time manually. The zenAmp gauges the time between taps and synchronizes the delay accordingly. TAP will of course only work when a delay effect is active. DELAY TYPE: Turn this rotary selector to choose from among the 16 different delay effects. This effects section can also be bypassed (see DELAY VOL). [. . . ] (Level/No) DLS compatible (Level(s)/No) Import DLS Files?(Type(s)/No) Import Standard MIDI Files (Type(s)/No) Export Standard MIDI Files (Type(s)/No) NOTES 1 Yes No No No No No No No No No No No No No No No No No Yes No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No No Yes No No No No No No No No No No No No No No No No No No No Data Dumps for Firmware Update Preset Transfers See Appendix 45 ZENAMP-MANUAL MIDI Implementation Chart v. 2. 0 (page 2 of 3) Manufacturer: Hughes & Kettner Model: ZenAmp Controller # Function Transmitted (Y/N) 0 Bank Select (MSB) No 1 Modulation Wheel (MSB) No 2 Breath Controller (MSB) No 3 4 Foot Controller (MSB) No 5 Portamento Time (MSB) No 6 Data Entry (MSB) No 7 Channel Volume (MSB) No 8 Balance (MSB) No 9 10 Pan (MSB) No 11 Expression (MSB) No 12 Effect Control 1 (MSB) No 13 Effect Control 2 (MSB) No 14 15 16 General Purpose Controller 1 (MSB) No 17 General Purpose Controller 2 (MSB) No 18 General Purpose Controller 3 (MSB) No 19 General Purpose Controller 4 (MSB) No 20 21 22 23 24 25 26 27 28 29 30 31 32 Bank Select (LSB) No 33 Modulation Wheel (LSB) No 34 Breath Controller (LSB) No 35 36 Foot Controller (LSB) No 37 Portamento Time (LSB) No 38 Data Entry (LSB) No 39 Channel Volume (LSB) No 40 Balance (LSB) No 41 42 Pan (LSB) No 43 Expression (LSB) No 44 Effect Control 1 (LSB) No 45 Effect Control 2 (LSB) No 46 47 48 General Purpose Controller 1 (LSB) No 49 General Purpose Controller 2 (LSB) No 50 General Purpose Controller 3 (LSB) No 51 General Purpose Controller 4 (LSB) No 52 53 54 55 56 57 58 59 60 61 62 63 Recognized (Y/N) No No No No No No No No No No No No No No No No Version: 1. 00 Remarks Date: 29. 03. 01/AP No No No No No No No No No No No No No No No No 46 ZENAMP-MANUAL MIDI Implementation Chart v. 2. 0 (page 3 of 3) Manufacturer: Hughes & Kettner Controller # Function Model: ZenAmp Transmitted (Y/N) No No No No No No No No No No No No No No No No No No No No No Recognized (Y/N) No No No No No No No No No No No No No No No No No No No No No Version: 1. 00 Remarks Date: 29. 03. 01/AP 64 Sustain Pedal 65 Portamento On/Off 66 Sostenuto 67 Soft Pedal 68 Legato Footswitch 69 Hold 2 70 Sound Controller 1 Sound Variation 71 Sound Controller 2 Timbre 72 Sound Controller 3 Release Time 73 Sound Controller 4 Attack Time 74 Sound Controller 5 Brightness 75 Sound Controller 6 Decay Time 76 Sound Controller 7 Vibrato Rate 77 Sound Controller 8 Vibrato Depth 78 Sound Controller 9 Vibrato Delay 79 Sound Controller 10 80 General Purpose Controller 5 81 General Purpose Controller 6 82 General Purpose Controller 7) 83 General Purpose Controller 8 84 Portamento Control 85 86 87 88 89 90 91 Effects 1 Depth Reverb Send Level 92 Effects 2 Depth 93 Effects 3 Depth Chorus Send Level 94 Effects 4 Depth 95 Effects 5 Depth 96 Data Increment 97 Data Decrement 98 Non-Registered Parameter N. [. . . ]