User manual HUMAX DRT800

[. . . ] The On-Screen Menus and the Remote Control Arrow Buttons To navigate the Recorder's on-screen menus, use the remote control's arrow buttons to move the highlight bar onto the option you want, then press SELECT. Select H U M A X D V D R e c o rd e r Vi e w e r's G u i d e The LEFT arrow button often takes you to the previous screen. Highlight Bar Select Two Types of On-Screen Arrows The arrows that appear beside or near the highlight bar show possible directions. For example, on this screen, you could press the RIGHT arrow to highlight Options or the DOWN arrow to highlight "Edit Category WishList. " Arrows Near Highlight Bar Viewer's Guide Page Up Arrow Page Down Arrow When you see page up or page down arrows at the top or bottom of the screen (or a list), press the CHAN UP/DOWN button to jump an entire page at a time. Setting up your HUMAX DVD Recorder Using the TiVo ® service Chan CHAN UP/DOWN Button P age Programming the Remote Control After you complete Guided Setup (see Chapter 2), you can program the TV POWER, VOL, and MUTE buttons to control your TV*: 1. Find the four-digit codes for your television brand. Press the TiVo button to go to TiVo Central®. [. . . ] Use the number buttons on the remote control to enter a four-digit code (starting with the first code in the list on the screen). After you press the fourth digit of the code, the red light on the end of the remote control should flash. Point the remote towards the TV and test the button: To Test the: Press the: TV power, volume, and mute TV POWER button TV input TV INPUT button A/V receiver power, volume, and mute TV POWER button A/V receiver volume and mute only MUTE button If pressing the button works (e. g. , turns the TV or A/V receiver off, or changes the TV input), the code is correct. If it does not work, repeat steps 3 and 4 using the next code on the list. If none of the codes works, perform a code search (see below). Performing a Code Search If none of the codes listed allows you to control your device, a code search may detect the correct code. Performing a code search can take up to 20 minutes. Point the remote away from your Recorder and cover the front end with your hand. Refer to the table below and determine which two buttons to press to prepare the remote. Press and hold the buttons simultaneously for about 5 seconds (until the red light at the end of the remote lights up and stays lit when you release the buttons). To Control: Press the: TV power, volume, and mute TV POWER and TiVo buttons TV input TV INPUT and TiVo buttons A/V receiver power, volume, and mute TV POWER and TiVo buttons A/V receiver volume and mute only MUTE and TiVo buttons 98 TiVo Central Messages & Setup Settings Remote Control & Recorder Front Remote Control & Recorder Front 2. Refer to the table below and use the number keys on your remote control to enter the appropriate code. To Test: Enter: TV power, volume, and mute 0999 TV input 0999 A/V receiver power, volume, and mute 1999 A/V receiver volume and mute only 1999 After you press the fourth digit of the code, the red light on the end of the remote control will flash twice, then remain on. Point the remote control at the TV or A/V receiver. The test is successful if the TV or A/V receiver responds (by powering off, changing input, or muting, depending on the function you are trying to program). If there is no response, wait two or three seconds, then press CHAN UP again. Continue doing this until the TV or A/V receiver responds. When the TV or A/V receiver does respond, press ENTER to select the current code. The red light at the end of the remote control will flash three times to indicate that the remote control is properly coded to control your device. When the red light on the end of the remote control turns off, you have reached the end of the available codes. Unfortunately, due to the great variety of TVs and A/V receivers, some makes and models are not compatible with your Recorder's remote control. If you reach the end of the available codes without finding a code that works with your device, you will need to use your TV or A/V receiver's remote to turn it on and off, and control the volume. 6 TiVo Central Messages & Setup Settings Remote Control & Recorder Front 99 Chapter 6 Messages & Setup By default, all TiVo DVRs and ® Managing Multiple Recorders and Remotes If you have more than one Recorder in your home, or if you have another model of TiVo DVR in addition to your HUMAX DVD Recorder, you can match a particular Recorder with a particular remote so that each Recorder will only respond to its own remote. You can do this by setting the Remote Address. If both Recorders are in the same room, start by covering the IR sensor window on one Recorder using a cloth or thick piece of paper. This will prevent setting the Remote Address on both Recorders simultaneously. [. . . ] Program will be recorded as part of a Season Pass. Program will be recorded as part of a WishList. TiVo Central, DVD, or Showcases Indicates a selection that has some special video content. Select to watch a special preview or visit a Showcase. Indicates news or a special promotional offer from TiVo. Indicates a playable DVD or photo CD is inserted. [. . . ]