User manual HUMAX DV-1100S

[. . . ] Notice ** Copyright (Copyright © 2001 HUMAX Corporation) ** Not to be copied, used or translated in part or whole without HUMAX's prior consent in writing except approval of ownership of copyright and copyright law. All rights reserved. ** Warranty ** The information in this document is subject to change without notice. HUMAX does not have any responsibility for direct, indirect, accidental, necessary and other damage due to your offer or use of the information contained in this manual. ** Trademarks ** VIACCESSTM is a trademark of France Telecom. CryptoWorks (TM) is a trademark of Philips Electronics N. V. [. . . ] Selects Disable if 22kHz Tone is not used. DiSEqC Input You can select DiSEqC switch. Select DiSEqC Input using the button, and press the OK or button. button, and press the Select the DiSEqC Swtich using the OK button. You can select one option among Tone burst A~B, DiSEqC A~D, DiSEqC A~D for 2. 0 and Disable. LNB Voltage You can raise the LNB Voltage value (select high ) preparing for the distance between antenna and receiver is further than 60m. Caution: If your set the LNB Voltage value as High when the distance between antenna and receiver is close, the LNB may be damaged. Set the LNB Voltage value using the OK ** or button. Standard High if the distance between antenna and receiver is within 60m if the distance between antenna and receiver is further than 60m GB 59 8. If you change the setting value to High, a message will prompt you to confirm. When the value is set to High, 1V higher than LNB voltage is supplied to LNB. 8. 2 Automatic Search If you select the satellite to search channel according to the Antenna Setting, you can automatically search the satellite without entering any other information. And You cannot watch any programme without searching channel. Select Installation using the button, and press the OK button. Select Automatic Search from Installation menu using the button, and press the OK or button. or Satellite You can select which satellite to search the channel. Select Satellite using the button, and press the OK or button. Select one of satellites using the button, and press the OK button. Note: Channel Search is performed only for the satellites that have been set to Enable in Antenna Setting - Satellite Alternative menu. If you wish to search channels for satellites, which is not listed on the Satellite List of Automatic Search, move to Antenna Setting and set the Satellite Alternative item as Enable. GB 60 * ** Search Type You can set search type to search by free channel or CAS type. Select All, FTA or CAS using the button. ** button, and press the OK button, and press the OK All FTA CAS Searches all channels. Searches channels for selected CAS. Note: The CAS type is Viaccess, Nagravision, Cryptoworks, and so on. Channel Type You can search by TV or Radio channel. Select Channel Type using the button, and press the OK or button. Select one option among All, TV and Radio using the button. ** All TV Radio Searches all channels. Searches only TV Channel. Scrambled Searches only Radio Channel. Search You can complete the setting and start searching. Select Search, and press the OK button to start Automatic Search. [. . . ] Specification ** Tuner & Channel Input Connector Frequency Range Signal Level LNB Power & Polarisation F-type, IEC-169-24, Female 950MHz to 2150MHz -10 to -93dBm Vertical: +13. 5V (+14. 5V at high voltage) Horizontal: +18V (+19V at high voltage) Current: 500mA Max. Overload Protection 22kHz Tone DiSEqC Control Demodulation Input Symbol Rate FEC mode MPEG Transport Stream A/V Decoding Transport Stream MPEG-2 ISO/IEC 13818 Transport Stream Specification Profile Level Video Input Rate Aspect Ratio Video Resolution Audio Decoding Audio Mode Memory Flash Memory Graphic (MPEG) & System DRAM EEPROM Available Disc(DVD) Available Reading MP3/Audio CD/VCD/CD/CD-R, RW/DVD-R, RW/DVD+R, RW, SVACD 4M byte 16M byte 16K byte MPEG2 MP@ML 15 Mbit/s Max 4:3, 16:9 , Letter box 720x576, 720x480 MPEG/MusiCam Layer I & II Single channel/Dual channel/Joint Stereo/Stereo Frequency: 22±4kHz Amplitude: 0. 6±0. 2V Version 1. 0 Compatible, USALS QPSK 1~45 Ms/s Convolutional Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8 with Constraint Length K=7 GB 111 Appendix 3. Specification ** A/V & Data In/Out Video Audio R/L RCA/SCART Video Output(CVBS, RGB, YPbPr) RCA/SCART Volume and Mute Control (Resolution: 20 bits DAC, MAX. 2Vrms) S/PDIF Digital Audio Output, Fiber-Optic (Resolution: 20 bits) RS-232C Power Supply Input Voltage Type Power Consumption Stand by Power Protection 90~250V AC, 50/60Hz SMPS Max. [. . . ]