User manual HUMAX HD-FOX IR

[. . . ] HD Digital Receiver The default password is 0000. User's Manual HD-FOX IR Notice Thank you for purchasing a HUMAX product. Please read this user's manual carefully to be able to safely install, use and maintain the product at maximum performance. Keep this user's manual next to your product for future reference. The information in this user's manual is subject to change without notice. Copyright (Copyright © 2008 HUMAX Corporation) Not to be copied, used or translated in part or whole without HUMAX's prior consent in writing except approval of ownership of copyright and copyright law. Warranty The warranty does not cover parts which may become defective due to misuse of the information contained in this manual. Trademarks · · Irdeto is a trademark of Irdeto Access B. V. [. . . ] If the required value is not available, select User Define and enter the LNB frequency directly. Note: If you select Universal, the 22kHz Tone will be set to Auto. 22kHz Tone Select Disable or Enable using the OK or / button. Enable Disable Dual LNB is used or two antennas are connected to the 22kHz tone switch box. 22kHz tone is not in use. DiSEqC Input Select the DiSEqC input option and press the OK button. LNB Power Select Standard or High and press the OK button. Transponder Set the transponder to check the signal status. If the required value is not available, select User Define and enter the transponder value directly. Select Search and press the OK button to go to search channels. GB57 User's Manual 9. Installation Select Search and press the OK button to go to search channels. 3. Search Channels Satellite Select All or the name of the satellite in antenna setting. Transponder Select All or the value in the transponder list and press the OK button. If the required value is not available, select User Define and enter the transponder value directly. Network Search Select Disable or Enable using the OK or / button. Scrambled Type Select among All, FTA and CAS and press the OK button. Channel Type Select among All, TV and Radio and press the OK button. To stop the search, press the OK button during channel search. Note: If there are no channels available, a message indicating the result will pop up. GB58 User's Manual 9. Set Transponder Transponder setting is normally fixed. Select User Define in Transponder and press the OK button. Enter the value for Frequency, Polarisation, Symbol Rate, Transmission, Modulation and FEC. Select Done and press the OK button to complete. Frequency Enter the frequency using the NUMERIC(0-9) buttons. Polarisation Select among Auto, Horizontal and Vertical and press the OK button. Symbol Rate Select the symbol rate and press the OK button. If the required symbol rate is not available, select User Define and enter the symbol rate directly. Transmission Select DVB or DVB-S2 and press the OK button. Modulation Select QPSK or 8PSK and press the OK button. FEC Select the FEC value and press the OK button. Note: When Transmission is set to DVB, Modulation is disabled. The values for Symbol Rate and FEC differ depending on the value of Modulation. Parameter Transmission Modulation Symbol Rate FEC DVB Disabled 2-45Ms/s Auto, 1/2, 2/3, 3/4, 5/6, 7/8 QPSK 10-30Ms/s Auto, 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10 Value DVB-S2 8PSK 10-31Ms/s Auto, 3/5, 2/3, 3/4, 5/6, 8/9, 9/10 GB59 User's Manual 9. Installation 9. 2 Antenna Setting [SCD Antenna] MENU Installation Antenna Setting [SCD Antenna] SCD Antenna Single Cable Distribution enables the delivery of broadcast programming over a single cable to multiple users eliminating the numerous cables required to support other electronics devices. If you are using more than one satellite receiver, set one receiver at a time and turn off the others while setting. Refer to the satellite antenna manual for details. [. . . ] The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. [. . . ]