User manual HUSQVARNA 123 L

[. . . ] Operator’s manual (EPA) 123C 123L 123LD Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Only intended for trimmer heads. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. [. . . ] The bevel gear can get hot during use and may remain so for a while afterwards. Never lean over the cutting attachment guard. can be thrown up into the eyes causing blindness or serious injury. Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m. Stop the machine immediately if anyone approaches. ! 10 – English WHAT IS WHAT? LD C What is what? 1 2 3 4 5 6 7 8 9 Trimmer head Grease filler cap Bevel gear Cutting attachment guard Shaft Loop handle Throttle control Stop switch Throttle lock 12 Fuel tank 13 Choke control 14 Air purge 15 Air filter cover 16 Handle adjustment 17 Drive disc 18 Socket spanner 19 Operator’s manual (EPA) 20 Allen key 21 Locking pin 22 Shaft coupling 10 Cylinder cover 11 Starter handle English – 11 ASSEMBLY Fitting the loop handle • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Hold both parts of the shaft and pull the lower part of the shaft out of the coupling. ! • • Fit the screw, securing plate and wing nut as shown in the diagram. Never use a cutting attachment without an approved guard. If an incorrect or faulty guard is fitted this can cause serious personal injury. Assembling and dismantling the two-piece shaft (123LD) Fitting the trimmer guard and trimmer head (123L, 123LD) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). Assembly: • Make sure the knob is loose. B C • Align the cut-out in the lower part of the shaft with the coupling locking tab on the upper part of the shaft. • • • • A • Fit the drive disc (B) on the output shaft. Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. Insert the locking pin (C) in the hole to lock the shaft. Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. H H Dismantling: • Undo the knob (at least three turns). • • • Push the knob towards the coupling. Carefully twist the lower half of the shaft to unlock it. To dismantle, follow the instructions in the reverse order. 12 – English ASSEMBLY Fitting the trimmer guard and trimmer head (123C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head • • • Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. Hold the dust cup with a spanner to prevent the shaft from rotating. Screw the trimmer head onto the shaft. English – 13 FUEL HANDLING Fuel CAUTION!The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. [. . . ] speed, left/right handles, max. : 2, 7/1, 5 3, 5/1, 7 5, 1/9, 3 7, 8/10, 9 1, 8/1, 4 2, 8/1, 8 3, 5/4, 1 8, 3/9, 1 1, 8/1, 4 2, 8/1, 8 7, 8/6, 2 10, 3/12, 1 91/98 91/97 91/97 8, 8/4, 0 9, 3/4, 2 9, 5/4, 3 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 WalbroMB/ SEM AM49 Champion RCJ 7Y 0, 02/0, 5 WalbroMB/ SEM AM49 Champion RCJ 7Y 0, 02/0, 5 WalbroMB/ SEM AM49 Champion RCJ 7Y 0, 02/0, 5 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-11700 11700 0, 65/7800 Yes No 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-11700 8014 0, 65/7800 Yes No 1, 50/24, 5 1, 34/34, 0 1, 06/27 2700 11000-11700 8014 0, 65/7800 Yes No 123L 123LD Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. English – 23 TECHNICAL DATA Approved accessories 123C Arbor shaft thread 3/8 RH Trimmer head Approved accessories 123L, 123LD Arbor shaft thread M10 LH Trimmer head Plastic blades Attachments Clean sweep attachment with shaft SR600 Edger attachment with shaft Saw attachment with shaft PA 1100 Saw attachment without shaft PA T35 Tricut Ø 300 mm Art No. 537 19 67-01 537 19 69-01 537 18 33-17 537 18 33-12 503 93 42-02 / 503 97 71-01 503 93 42-02 Use with 123LD 123LD 123LD 123L, 123LD Trimmy Hit VII (R) Type 537 02 61-01 Cutting attachment guard, Art. [. . . ]