User manual HUSQVARNA 136

[. . . ] This symbol indicates that the machine is in conformance with the applicable European directive. The disc cutter is designed to provide safe and reliable service in operating conditions corresponding with the instructions, but it can present dangers for the user and risks of damage, consequently regular on site inspection is necessary to ensure : · Perfect technical condition (use for the purpose for which it is intended and taking into account any risks, and correction of any malfunction detrimental to safety). Use of a diamond disc for water lubricated cutting of marble, stone, granite, brick and facings (porcelain, glazed tiles, ceramics, etc). The use of any other disc is forbidden (abrasive, saw, etc). [. . . ] That the warnings and instructions marked on the machine are followed (adequate personal protection, correct use, general safety instructions, etc). That no modification, transformation or addition is detrimental to safety and that it is carried out without prior authorization from the manufacturer. That only genuine spare parts are used for repairs. Any application not corresponding with the intended use (use of a saw blade, abrasive disc, etc) is prohibited. Unladen weight : ± 92 kg (depending on model) - chassis : 56 kg - head : 36 kg · Use : Sawing marble, stone, granite, brick, cement and all facings (porcelain, glazed tiles, ceramics, etc). check the supply cable lead periodically. 1 PLACING ON FEET (SEE FIG 8) 1 Chassis-tank 2 Leg 3 Head clamping handle 4 Water pump 5 Lifting lever 6 Locking handle 7 Loading leg 8 Drain plug 9 Motor 10 Lack of voltage switch 11 Hood 12 Disc casing 13 Housing cover 14 Movable table 15 Table stop 16 Movable table stop 17 Manufacturer's plate 18 Cutting guide 19 Table locking 20 Carrying handles 21 Transport wheels 22 Water tank 23 Water level 4 Handling - transport Inspection before starting Please read the instructions for use prior to operating the machine for the first time. The use of ear protection is mandatory. The working area must be completely cleared, well lit and all safety hazards removed (no water or dangerous objects in the vicinity). Any persons not involved in the work should leave the working area. Use blades suitable for the work to be done (speed, geometry, application, etc. Single phase motor starting condenser Repairs Contact your supplier who is entirely at your service to carry out repairs in the shortest time at the best possible price. The machine is set before leaving the factory and no adjustment is necessary. However, after shocks, loosening of nuts and bolts, or sharp movements when tilting the head, if necessary adjust the stop screws(D) and check the squareness (for straight cuts) . To correct the bevel cutting setting, adjust the stop screw (E) and lock the nut with a lock- nut (SEE FIG. For rapid delivery of spares and in order to avoid any wasted time, it is necessary to remind your supplier of the details shown on the instruction plate on the machine with each order, as well as the reference of the part to be replaced. In the event of a long period of use pay special attention to the maintenance and protection of the disc. Make sure that sufficient water is sprayed onto the disc. Make sure that the contact faces of the disc, the flanges and the spindle are clean. The manufacturer declines all responsibility for loss or damage resulting from misuse or any modification, alteration or powering that does not conform to the manufacturer's original specifications. In the event of deterioration and scrapping of the machine, the following items must be disposed of in accordance with the requirements of the legislation in force. At the work station, the sound pressure level may exceed 85 db (A) In this case individual protection measures must be taken. [. . . ] At the work station, the sound pressure level may exceed 85 db (A) In this case individual protection measures must be taken. The instructions for use and spare parts found in this document are for information only and are not binding. As part of our product quality improvement policy, we reserve the right to make any and all technical modifications without prior notice. Anslutning till nätet med en kabel typ H07 RNF med tvärsnittsarea: - 3 x 2, 5 mm2 upp till 50 m för 230 V - 4 eller 5 x 1, 5 mm2 upp till 100 m för 400 V - 3 x 4 mm2 upp till 40 m för 115 V Vi finns alltid till hands för dig för att reparera din maskin inom kortast möjliga tid och till våra bästa priser (adressen finns på baksidan). [. . . ]