User manual HUSQVARNA 210 C 2010

[. . . ] h u sqvarna AUTOMOWE R ® 210 C ope r ator’s man ual TABLE OF CONTENTS 1. Introduction and safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 Symbols on Automower® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It will then be easier to lay the wire close to the ground and the risk of the mower cutting the wire off is reduced. 22 - English 3. INSTALLATION • Make sure to lay the boundary wire tight to the ground and secure the staples close together with approximately 75 cm (30”) between each staple. The wire must generally lie close to the ground, so as not to be cut off before the grass roots have grown over it. Use a hammer to knock down the staples in the ground. Exercise care when knocking in the staples and make sure the wire is not under strain. Avoid forming the wire in sharp bends. • If you intend to bury the boundary wire: • Make sure to place the boundary wire at least 1 cm (0. 5") and a maximum of 20 cm (8") into the ground. The boundary wire must not be crossed on the path to and from an island. Laying the boundary wire in towards the loop generator/charger The ends of the boundary wire are run in parallel and close to each other in towards the loop generator/charger. As long as the total length of the boundary wire does not exceed 350 m (1200 ft), the sections where the wires run in parallel can be any length. For example, it is possible to place the loop generator/charger inside the house and run the boundary wire through a window and out to the garden. IMPORTANT INFORMATION Pay particular attention not to cross the boundary wire in towards the loop generator/charger. English - 23 3. INSTALLATION Joining the boundary wire If the boundary wire is not long enough and needs to be spliced: Use original solderless coupler. It is waterproof and gives a reliable electrical connection. To splice: Insert both cable ends in the coupler. Now press down the button on top of the connector fully. Use a pair of pliers or the like, as the button on the connector is difficult to press down by hand. IMPORTANT INFORMATION Twisted cables, or a screw terminal (chock-block), insulated with insulation tape is not a satisfactory splice. Soil moisture will cause the conductors to oxidize and after a while result in a broken circuit. 3. 5 Connecting the boundary wire Connect the boundary wire to the loop generator/charger: 1. Place the cable ends in the connector: • Open the connector. • Place the wire in the connector grip. 2. Press the connector together using a pair of pliers. Press until you hear a click. 24 - English 3. Cut 1 à 2 cm (0. 4" - 0. 8") above respective connectors. 4. Attach the connector to the contact pin on the loop generator/charger. 3. 6 Checking the installation Check the loop signal by looking to see what indication the green LED on the loop generator/charger is giving. • • • Steady light = the signal is okay. Flashing once every other second = break in the loop and no signal found. Flashing twice every other second = weak signal. [. . . ] Check the blade disc and remove the grass or other object. 5 42 - English 8. TROUBLE SHOOTING 8. 2 Fault symptom If your Automower® does not work correctly, follow the trouble shooting guide below. If the fault persists; contact your dealer. Symptom Uneven mowing results Cause Automower® works too few hours per week. [. . . ]