User manual HUSQVARNA 225 RJ

[. . . ] 225R/RD/RJ 232R/RD 235R Operator's Manual (CARB, EPA) 101 89 27-95 Read through the Operator's Manual carefully and understand the content before using the machine. SYMBOL EXPLANATION Symbols WARNING!Clearing saws, brush cutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. [. . . ] Constant contact can cause damage and wear to the trimmer head. Sweeping • The rotating cord‘s fanning effect can be used for quick and easy cleaning. Hold the cord parallel to and above the area to be swept and move the trimmer from side to side. • When cutting and sweeping you should use full throttle to obtain the best results. ! WARNING!can be thrown up into the eyes causing blindness or serious injury. Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m (50 feet). Stop the machine immediately if anyone approaches. 14 – English WHAT IS WHAT? 27 28 30 What is what on the brush cutter? 1. Spray guard English – 15 ASSEMBLY Assembling the handlebars (225R/RD/ 232R/RD) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Unscrew the handle from the handlebar bracket. • Position the handlebars as shown. Fit the bracket components and tighten the handle lightly. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it‘s attached to the harness. Tighten the handle. Assembling the handlebars (235R) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. [. . . ] 503 74 40-01 503 74 40-01 503 74 40-01 503 74 40-01 503 77 39-01 503 74 40-01 503 74 50-01 503 74 50-01 503 74 50-01 503 74 50-01 - Saw blade Plastic knives Trimmer head Edger (RD) Support cup Approved accessories 235R Centre hole in blades Ø 20 mm Threaded blade axle M12 Grass blade Type Cutting attachment guard Ref No. 502 26 34-01 502 26 34-01 502 26 34-01 502 27 22-01 502 26 34-01, 503 91 60-01 503 91 60-01 503 91 60-01 - Saw blade Plastic knives Trimmer head Support cup Multi 255-3 (∅ 255 3-teeth) Multi 275-4 (∅ 275 4-teeth) Multi 300 (∅ 300 3-teeth) Maxi X 200-26 (∅ 200 26-teeth) Tricut ∅ 300 Trimmy SII Trimmy S Fixed With bearing English – 29 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U. S. Environmental Protection Agency), Carb (California Air Resources Board) and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1997 and later Lawn and Garden Equipment Engine. In U. S. , new utility and lawn and garden equipment engines must be designed, built and equipped to meet the federal and California stringent anti-smog standards. [. . . ]