User manual HUSQVARNA 232 RD

[. . . ] 225R/RD/RJ 227R/RD 232R/RD 235R Operator's Manual (CARB, EPA) 101 89 79-95 Read through the Operator's Manual carefully and understand the content before using the machine. SYMBOL EXPLANATION Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. [. . . ] • When cutting and sweeping you should use full throttle to obtain the best results. ! WARNING!can be thrown up into the eyes resulting in blindness or other serious injury. Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be outside the safety zone of 15 meters (50 feet). Stop the machine immediately if anyone approaches. 16 – English WHAT IS WHAT? 33 27 28 30 What is what on the brushcutter? 1. Blade Grease filler cap Angle gear Blade guard Shaft Handlebars Throttle Stop switch Throttle trigger lock Suspension for clearing saw Cylinder cover Starter handle Fuel tank Choke Air filter cover Clutch cover Handlebar adjustment 18. Locking nut Support flange Support cup Drive disc Trimmer head J-handle (RJ) Shaft coupling Socket spanner Operator‘s Manual Transport guard Allen key Locking pin Harness Spray guard Air purge English – 17 ASSEMBLY Assembling the handlebars (225R/RD, 227R/RD, 232R/RD) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Unscrew the handle from the handlebar bracket. • Position the handlebars as shown. Fit the bracket components and tighten the handle lightly. • Put on the harness and hang the machine in the suspension hook. Now finely adjust so that the machine gives a comfortable working position when it‘s attached to the harness. Tighten the handle. Assembling the handlebars (235R) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle handle. • Fit the screw through the throttle handle and the handlebars and tighten. • Unscrew the bracket components from the handlebar bracket. [. . . ] The table indicates the highest and lowest values. English – 31 TECHNICAL DATA Approved accessories 225R/RD/RJ, 227R/RD Centre hole in blades Ø 20 mm Threaded blade axle M10 Grass blade Type Cutting attachment guard Art No. Saw blade (Not 225RJ) Plastic knifes Trimmer head Edger (RD) Support cup Grass 255-4 (∅ 255 4-teeth) Grass 255-8 (∅ 255 8-teeth) Multi 255-3 (∅ 255 3-teeth) Maxi X 200-26 (∅ 200 26-teeth) Tricut ∅ 300 Trimmy H II Trimmy Hit Trimmy Hit Pro Trimmy Fix Superauto II Edger attachment ∅ 200 Fixed 503 74 40-01 503 74 40-01 503 74 40-01 503 77 39-01 503 74 50-01 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 - Approved accessories 232R/RD Centre hole in blades Ø 20 mm Threaded blade axle M10 Grass blade Type Grass 255-4 ( ∅ 255 4-teeth) Grass 255-8 ( ∅ 255 8-teeth) Multi 255-3 ( ∅ 255 3-teeth) Multi 275-4 ( ∅ 275 4-teeth) Maxi X 200-26 (∅ 200 26-teeth) Tricut ∅ 300 Trimmy H II Trimmy Hit Trimmy Hit Pro Trimmy Fix Superauto II Edger attachment ∅ 200 Fixed Cutting attachment guard Ref No. 503 74 40-01 503 74 40-01 503 74 40-01 503 74 40-01 503 77 39-01 503 74 40-01 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 - Saw blade Plastic knives Trimmer head Edger (RD) Support cup Approved accessories 235R Centre hole in blades Ø 20 mm Threaded blade axle M12 Grass blade Type Cutting attachment guard Ref No. 502 26 34-01 502 26 34-01 502 26 34-01 502 27 22-01 502 26 34-01, 503 74 50-04 503 74 50-04 503 74 50-04 - Saw blade Plastic knives Trimmer head Support cup Multi 255-3 (∅ 255 3-teeth) Multi 275-4 (∅ 275 4-teeth) Multi 300 (∅ 300 3-teeth) Maxi X 200-26 (∅ 200 26-teeth) Tricut ∅ 300 Trimmy SII Trimmy S Fixed With bearing 32 – English FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U. S. Environmental Protection Agency), CARB (California Air Resources Board) and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1999 and later small off-road engine. [. . . ]