User manual HUSQVARNA 240 F

[. . . ] Operator’s manual (EPA) 240F 240R 250R 252RX 265RX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols Always wear approved protective gloves. Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Regular cleaning is required. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • • • A protective helmet where there is a risk of falling objects Hearing protection Approved eye protection Visual check. Approved eye protection must always be used. Max. [. . . ] Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation. Gasoline, litre 5 10 15 20 US gallon 1 2 1/2 5 Two-stroke oil, litre 2% (1:50) 0, 10 0, 20 0, 30 0, 40 US fl. 2 1/2 6 1/2 12 7/8 ! English – 21 FUEL HANDLING Mixing • • Always mix the gasoline and oil in a clean container intended for fuel. Always start by filling half the amount of the gasoline to be used. Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. Fueling • ! WARNING!Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently. Tighten the fuel cap carefully after refuelling. Always move the machine away from the refuelling area before starting. • • Do not mix more than one month’s supply of fuel at a time. If the machine is not used for some time the fuel tank should be emptied and cleaned. The catalytic converter muffler gets very hot during and after use. Be aware of the fire hazard, especially when working near flammable substances and/or vapours. • • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. Ensure that the fuel is well mixed by shaking the container before filling the tank. ! 22 – English STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. Discard a blade if cracks are found. ! WARNING!The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. Always move the machine away from the refuelling area before starting. Ensure the cutting attachment cannot come into contact with any object. Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. [. . . ] no. Approved accessories 250R Centre hole in blades/cutters, Ø 20 mm Grass blade/grass cutter Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Maxi XS 200-22 (Ø 200 22 teeth) Maxi XS 225-22 (Ø 225 22 teeth) Tricut Ø 300 mm Trimmy S Trimmy S II Auto 55 With ball bearing - Cutting attachment guard, Art. 502 26 34-01 502 26 34-01 502 26 34-01 502 27 22-01 502 03 94-03 503 91 60-01 / 502 26 34-01 503 91 60-01 503 91 60-01 503 91 60-01 Set 537 16 55-01 Saw blade Plastic blades Trimmer head Support cup Chopping blade Approved accessories 252RX Centre hole in blades/cutters, Ø 20 mm Grass blade/grass cutter Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Maxi XS 200-22 (Ø 200 22 teeth) Maxi XS 225-22 (Ø 225 22 teeth) Trimmy S Trimmy S II Auto 55 With ball bearing Cutting attachment guard, Art. 502 26 34-01 502 26 34-01 502 26 34-01 502 27 22-01 502 03 94-03 503 91 60-01 503 91 60-01 503 91 60-01 - Saw blade Trimmer head Support cup Approved accessories 265RX Centre hole in blades/cutters, Ø 20 mm Grass blade/grass cutter Saw blade Type Output shaft thread M12 Multi 300-3 (Ø 300 3 teeth) Maxi XS 200-22 (Ø 200 22 teeth) Maxi XS 225-22 (Ø 225 22 teeth) Opti 255-22 (Ø 255 22 teeth) Trimmy S Trimmy S II With ball bearing Cutting attachment guard, Art. 502 26 34-01 502 27 22-01 502 03 94-03 502 03 95-03 503 91 60-01 503 91 60-01 - Trimmer head Support cup English – 37 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. [. . . ]