User manual HUSQVARNA 323 E

[. . . ] Operator's manual (EPA II) 323E 325EX-series Please read these instructions carefully and make sure you understand them before using the machine. English EXPLANATION OF SYMBOLS Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. • Arrows which show limits for handle mounting. • Always wear approved protective gloves. Read through the Operator's Manual carefully and understand the content before using the machine. • Use anti-slip and stable boots. Always use: • A protective helmet where there is a risk of falling objects. • Ear protection • Approved eye protection Other symbols/decals on the machine refer to special certification requirements for certain markets. max 10000 rpm • Max. [. . . ] The support flange must be fitted with its outer edge hard up against the blade. The tightening torque of the locknut is 35 – 50 Nm. Remove the locking pin. A B C D 2. 3. 4. 5. 6. Assembling the angle gear • Assemble the angle gear back on the supporting tube. Turn the blade so that the drive shaft engages in the angle gear. Do not forget to remove the locking pin before using the machine. • Position the angle gear so that its slot is aligned with the line on the supporting tube. ! WARNING!Under no circumstances may the edge cutter blade be used without the blade guard fitted. • Firmly tighten the screw. English – 13 FUEL HANDLING Fuel mixture NOTE!The edger is fitted with two-stroke engines and must always be run on a mixture of gasoline and two-stroke oil. To ensure the correct mixture proportions it is important to measure the quantity of oil accurately. When mixing small amounts of fuel small discrepancies in the amount of oil has a great bearing on the proportions of the fuel mixture. Mixture • Always mix gasoline and oil in a clean container intended for fuel. • Always start by filling half the quantity of gasoline required. Fill the remaining quantity of gasoline. • Mix (shake) the fuel mixture carefully before filling in the machine‘s fuel tank. • If the clearing saw is not used for a long period of time, the fuel tank should be emptied and cleaned. • This engine is certified to operate on unleaded gasoline. ! Gasoline WARNING!Always provide good ventilation when handling fuel. NOTE!Always use high grade unleaded oil mixed gasoline (minimum 87 RON). Leaded fuel will destroy the catalytic converter and it will no longer serve its purpose. • This engine is certified to operate on unleaded gasoline. • The lowest recommended octane rating is 87. If you run the engine on lower octane rating than 87 so-called “knocking“ can occur. This leads to an increased engine temperature, which can result in a serious engine breakdown. [. . . ] to ISO 8893 Catalytic converter muffler Speed-regulated ignition system 1, 50/24, 5 1, 34/34 1, 06/27 11 000 - 11 700 2 700 8 300 0, 9 kW/ 9 000 rpm No Yes 1, 50/24, 5 1, 34/34 1, 06/27 11 000 - 11 700 2 700 8 300 0, 9 kW/ 9 000 rpm Yes Yes 323E 325EX-series Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Walbro MB 21 Champion RCJ 7Y 0, 02/0, 5 Walbro MB 21 Champion RCJ 7Y 0, 02/0, 5 Fuel lubrication system Manufacturer/type of carburetor Fuel tank capacity, US pint/litres Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 Weight Weight without fuel and cutting tool, Lbs/kg 10, 8/4, 9 11, 2/5, 1 Sound levels (see note 1) Equivalent sound pressure levels at the user‘s ear, measured according to EN ISO 11806 and ISO 11789, dB(A) Equivalent sound power levels measured according to EN ISO 11806 and ISO 10884, dB(A) 94 96 100 102 Vibration levels Vibration levels on the handles measured according to EN ISO 11806 and ISO 11789, m/s2 When idling, rear/front handles: At max. speed, rear/front handles: 4, 0/2, 0 7, 3/5, 9 1, 4/2, 6 6, 0/4, 4 Cutting equipment Blade Blade guard 503 84 82-02 503 84 65-01 503 84 82-02 503 84 65-01 Note 1: Equivalent sound level is calculated as the time-weighted energy total for sound levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max speed. English – 21 EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards. Husqvarna Forest & Garden must warrant the emission control system on your small nonroad engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. [. . . ]