User manual HUSQVARNA 323 LD

[. . . ] Operator’s manual (EPA) 323C 325CX 323L 325LX 323LD 325LDX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. [. . . ] Note that the loop handle must be fitted between the arrows on the shaft. Dismantling: • Undo the knob (at least three turns). • • • • Slide the spacer into the slot in the loop handle. 325Lx/325LDx: Fit the nut, knob and screw. • Now adjust the trimmer to give a comfortable working position. • Push the knob towards the coupling. Carefully twist the lower half of the shaft to unlock it. Hold both parts of the shaft and pull the lower part of the shaft out of the coupling. 12 – English ASSEMBLY Fitting the trimmer head When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution!left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. ! WARNING!Never use a cutting attachment without an approved guard. If an incorrect or faulty guard is fitted this can cause serious personal injury. Fitting a trimmer guard and Superauto II 1" trimmer head (323L, 325Lx, 325LDx) • To dismantle, follow the instructions in the reverse order. Fitting other guards and cutting attachments (323L, 325Lx, 325LDx) K K J I G F I • B C Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). A • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). Fit the drive disc (B) on the output shaft. Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. Insert the locking pin (C) in the hole to lock the shaft. To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows: Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). Pull apart the trimmer head, grasping the cover firmly. Place the cover (I) and the support flange (F) on the output shaft. The nut must be tightened to a torque of 35-50 Nm (3. 5-5 kpm). [. . . ] no. 325Cx Approved accessories Blade shaft thread 3/8 R Trimmer head Trimmy Fix 3/8” (R) Trimmy Hit VII (R) Trimmy Hit Junior (R) 537 07 67-01 537 07 67-01 537 07 67-01 Type Cutting attachment guard, Art. no. 323L, 325Lx, 325LDx Approved accessories Arbor shaft thread M10 Plastic blades Grass blade/grass cutter Trimmer head Tricut Ø 300 mm Grass 255-8 1" (Ø 255 8-teeth) Trimmy Fix Superauto II 1" S35 T35 503 93 42-02 503 93 42-02 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 Type Cutting attachment guard, Art. no. Attachments Clean sweep attachment with shaft SR600 Hedge trimmer attachment with shaft HA 110 Hedge trimmer attachment with shaft HA 850 Edger attachment with shaft Saw attachment with shaft PA 1100 Saw attachment without shaft PA Trimmer attachment with shaft TA 850 Art No. 537 19 67-01 537 19 66-01 537 19 66-02 537 19 69-01 537 18 33-17 537 18 33-12 537 35 35-01 Use with 325LDx 325LDx 325LDx 325LDx 325LDx 323L, 325Lx 325LDx 24 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engine. [. . . ]