User manual HUSQVARNA 3232 R

[. . . ] Operator’s manual (EPA) 232R 235R 235FR Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. [. . . ] Wash any part of your body that has come in contact with fuel. Check regularly for leaks from the fuel cap and fuel lines. Gasoline 3 CAUTION!Always use a quality gasoline/oil mixture with an octane rating of at least 87 octane ((RON+MON)/2). If your machine is equipped with a catalytic converter (see chapter on Technical data) always use a good quality unleaded gasoline/oil mixture. Leaded gasoline will destroy the catalytic converter. Use low-emission gasoline, also known as alkylate gasoline, if it is available. Transport and storage • Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/ switches or boilers. When storing and transporting fuel always use approved containers intended for this purpose. When storing the machine for long periods the fuel tank must be emptied. Contact your local gas station to find out where to dispose of excess fuel. Ensure the machine is cleaned and that a complete service is carried out before long-term storage. The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. In order to prevent unintentional starting of the engine, the spark plug cap must always be removed during long-term storage, if the machine is not under close supervision and when performing all service measures. • • This engine is certified to operate on unleaded gasoline. • The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage. When working at continuous high revs a higher octane rating is recommended. • • • • Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). Never use oil intended for four-stroke engines. Mixing ratio 1:50 (2%) with HUSQVARNA two-stroke oil. Gasoline, litre 5 Two-stroke oil, litre 2% (1:50) 0, 10 0, 20 0, 30 0, 40 US fl. 2 1/2 6 1/2 12 7/8 ! Fuel WARNING!Bear in mind the risk of fire, explosion and inhaling fumes. • CAUTION! [. . . ] speed, left/right handles, min. : At max. speed, left/right handles, max. : 2, 5/2, 5 3, 0/3, 5 2, 0/2, 0 5, 1/4, 9 2, 6/2, 8 3, 2/4, 0 4, 6/3, 0 9, 3/6, 4 90/100 98/100 14, 3/6, 5 16, 1/7, 3 Walbro WT 1, 06/0, 5 Walbro WT 1, 06/0, 5 Walbro CD NGK BPMR 7A/ Champion RCJ 7Y 0, 02/0, 5 Walbro CD NGK BPMR 7A/ Champion RCJ 7Y 0, 02/0, 5 1, 88/30, 8 1, 38/35 1, 26/32 2700 11000-11700 10000 1, 1/8400 Yes Yes 2, 45/40, 2 1, 57/40 1, 26/32 2700 11500-12500 10000 1, 3/9000 Yes Yes 232R 235R, 235FR Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. 34 – English TECHNICAL DATA Approved accessories 232R Centre hole in blades/cutters, Ø 25, 4 mm Arbor shaft thread M10 Grass 255-4 (Ø 255 4 teeth) Grass blade/grass cutter Grass 255-8 (Ø 255 8 teeth) Multi 255-3 (Ø 255 3 teeth) Multi 275-4 (Ø 275 4 teeth) Saw blade Plastic blades Maxi X 200-26 (Ø 200 26 teeth) Tricut Ø 300 mm S35 T35 Trimmer head Trimmy Hit Trimmy Hit Pro Trimmy Fix Superauto II Support cup Approved accessories 235R, 235FR Centre hole in blades/cutters, Ø 25, 4 mm Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S II T35, T35x Trimmer head T45x S35 F35 Auto 55 Support cup Fixed With ball bearing 537 33 16-01 537 33 16-01 537 33 16-01 537 38 77-01 537 33 16-01 / 537 34 94-01 537 33 16-01 / 537 34 94-01 537 33 16-01 / 537 34 94-01 537 33 16-01 / 537 34 94-01 537 33 16-01 / 537 34 94-01 537 33 16-01 / 537 34 94-01 537 33 16-01 / 537 34 94-01 Fixed Type 503 74 40-01 503 74 40-01 503 74 40-01 503 74 40-01 503 77 39-01 503 74 50-01 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 503 74 50-04 Cutting attachment guard, Art. [. . . ]