User manual HUSQVARNA 325 LX

[. . . ] Operator’s manual (EPA) 323C 325CX 323L 325LX 325LDX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Clearing saws, brushcutters and trimmers can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. [. . . ] Carefully twist the lower half of the shaft to unlock it. Hold both parts of the shaft and pull the lower part of the shaft out of the coupling. • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Fitting the trimmer head When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. • • Slide the spacer into the slot in the loop handle. 325Lx/325LDx: Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft (325LDx) ! WARNING!Never use a cutting attachment without an approved guard. If an incorrect or faulty guard is fitted this can cause serious personal injury. Assembly: • Make sure the knob is loose. 12 – English ASSEMBLY Fitting a trimmer guard and Superauto II trimmer head (323L, 325Lx, 325LDx) Fitting other guards and cutting attachments (323L, 325Lx, 325LDx) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). K J I G F I B C K A • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). Fit the drive disc (B) on the output shaft. Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. Insert the locking pin (C) in the hole to lock the shaft. To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows: Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). Pull apart the trimmer head, grasping the cover firmly. Place the cover (I) and the support flange (F) on the output shaft. The nut must be tightened to a torque of 35-50 Nm (3. 5-5 kpm). Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (left-hand thread). [. . . ] Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. 24 – English TECHNICAL DATA 323C Approved accessories Blade shaft thread 3/8 R Trimmer head Trimmy Hit Junior (R) Trimmy Fix 3/8” (R) Trimmy Hit VII (R) 537 02 61-01 537 02 61-01 537 02 61-01 Type Cutting attachment guard, Art. no. 325Cx Approved accessories Blade shaft thread 3/8 R Plastic blades Trimmer head Tricut Ø 230 mm (R) Trimmy Fix (R) Trimmy Hit VII (R) 537 07 67-01 537 07 67-01 537 07 67-01 Type Cutting attachment guard, Art. no. 323L, 325Lx, 325LDx Approved accessories Blade shaft thread M10 Plastic blades Trimmer head Tricut Ø 300 mm Trimmy Fix Trimmy H II 1" Trimmy Hit Trimmy Hit Pro Superauto II 1" S35 T35 503 93 42-02 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 503 93 42-02 / 503 97 71-01 Type Cutting attachment guard, Art. [. . . ]